background image

13

Air filtration

If the EPA filter (A7) is installed, in addition to operating in the 
preset mode, the appliance will also filter the air in the room.  In 
this case, the   symbol (C2) will appear on the display.
The filter is designed to last up to 9 months, based on 8-hour 
daily usage at medium working load. 
To maintain the efficiency of filtration, see paragraph “5.3 
Replacing the EPA filter”.

9.1  Dehumidifying mode

1.  Touch the 

 button (B3).  The   symbol (C9) will 

blink on the display (fig. 7).

2.  The display shows the previously set relative humidity 

value. When the   symbol blinks, the setting can be 
changed by repeatedly touching the 

  button.                                                                                                                                          

There are 9 different relative humidity settings ranging 
from  30%  (dry  environment)  to  70%  (humid  environment).                                                                                                                                    
Depending on the environmental conditions, it may not be 
possible for the appliance to reach the minimum settable 
value. In these cases, it is recommended the heat the 
environment that needs to be dehumidified.

3.  When the   symbol stops blinking, the display shows the 

percentage of relative humidity in the room. The appliance 
may take a few seconds to display the value of the relative 
humidity in the room. 

4.  When the room reaches the preset relative humidity level, 

the appliance stops dehumidifying and operates at a very 
slow ventilation speed.

9.2  Dry mode

1.  Touch the 

button (B6).  The display shows the   

symbol (C7) (fig. 8).

Please note:

The appliance automatically operates at the maximum 
dehumidifying capacity. Recommended for particularly humid 
environments or to dry laundry more quickly.

9.3  Ventilation mode

1.  Touch the 

button (B2).  The display shows the   

symbol (C3) and the selected speed (fig. 9).

2.  When the   symbol blinks, the ventilation speed can be 

adjusted by repeatedly pressing the  

button. the 

display shows the number corresponding to the selected 
speed (1 

 LOW; 2 

 MED; 3 

 HIGH).

9.4  Swing function

1.  Press the button (B5) 

. The air outlet louver (A1) 

moves up and down, evenly distributing the air flow in the 
room (fig. 10).

2.  To stop the louver in the desired position, touch the same 

button again.

9.5  Timer function

The timer can be used to delay appliance start-up and shut-
down.  This will avoid energy wastage, ensuring the appliance 
operates only when needed.
The timer function can be programmed from either the control 
panel or the app.

•  If programmed from the control panel: the display shows 

the   symbol (C12) (fig. 11).

•  If programmed from the app: the display shows the   

symbol (C11) (fig. 12). To programme the timer from the 

app, follow the instructions provided in the app.

How to programme delayed start-up

1.  With the appliance in stand-by (

), touch the 

 

button (B7): the display will show the   symbol and the 
number relative to the selected hours (fig.11);

2.  Set the desired number of hours by repeatedly touching 

the 

 button.1, 2, 4, 6, 8, 12 hours can be selected.

3.  After a few seconds, the appliance will return to stand-by 

mode and the   symbol will remain lit on the display.

4.  After the programmed time, the appliance will turn on in 

the previously set operating mode.

How to programme delayed shut-down

1.  While the appliance is running, touch the 

 button 

(B7): the display shows the   symbol and the relative 

number of selected hours (fig. 11);

2.  Set the desired number of hours by repeatedly touching the 

 button. 1, 2, 4, 6, 8, 12 hours can be selected.

3.  After a few seconds, the display returns to the current 

operating mode and the   symbol remains lit.

4.  After the programmed time, the appliance will 

automatically turn off.

Please note:

•  Once the timer has been programmed, to see the remaining 

time until start-up or shut-down, touch the 

 

button once.

•  To deactivate the timer function, press the

 button 

twice. The    symbol on the display will turn off.

9.6  Wi-Fi function

The appliance has a built-in Wi-Fi function. To activate or 
deactivate this function, hold the 

 button (B4) pressed 

until the appliance emits two beeps. When the Wi-Fi function is 
active, the display will show the   Wi-Fi symbol (C5) with the 
following operating modes:

 

-

   FIXED

  this means the Wi-Fi functions are active and the  

  “Home WLAN” has been found

 

-

    SLOW FLASHING

  this means the appliance is searching for the  

  “Home WLAN”

Summary of Contents for DDSX 220WF-WH














Reviews: