background image

15

11.  Empty the container used to collect the rinsing water. Re-

move the water tank, replace the water softener filter (if 
removed previously), fill the tank up to the MAX level with 
cold water and insert in the appliance. The 

 steam 

light flashes.

12.  Place the container used to collect the rinsing water empty 

under the cappuccino maker;

13.  Turn the steam/hot water dial to the 

I

 position. Rinsing 

continues from the cappuccino maker only.

14.  When it finishes, the 

 steam light flashes on the con-

trol panel. Turn the steam/hot water dial to the 

0

 position.

15.  Top up the water tank with fresh water to the MAX level 

and put back in the machine.

The descaling cycle is now complete.

 Please note! 

•  If the descaling cycle is not completed correctly (e.g. no 

electricity) we recommend repeating the cycle;

•  After descaling, it is normal for the grounds container 

(A13) to contain water;

•  If the water tank has not been filled to the MAX level, at 

the end of descaling, the appliance requests a third rinse to 

guarantee that the descaler solution has been completely 
eliminated from the machine's internal circuits.

18.  SETTING WATER HARDNESS

Descaling is necessary after a period of operation established 
according to the water hardness set. 
The machine is set by default for a hardness level of 4. The ma-
chine can also be programmed according to the hardness of the 
mains water in the various regions so that the machine needs to 
be descaled less often.

18.1  Measuring water hardness

1.  Remove the “TOTAL HARDNESS TEST” indicator paper (C1) 

from its pack (attached to the English instructions);

2.  Immerse the paper completely in a glass of water for one 

second;

3.  Remove the paper from the water and shake lightly. After 

about a minute, 1, 2, 3, or 4 red squares form, depending 
on the hardness of the water. Each square corresponds to 
one level;

Indicator paper

Water 

hard-

ness

Corresponding 
setting

low

medium

high

 

m a x i -
mum

 

18.2  Setting water hardness

1.  Make sure the appliance is off (but connected to the mains 

electricity supply and with the main switch (A6) in the I 
position);

2.  Press and hold the 

 button (B5) for at least 5 seconds. 

The  , 

 and 

 lights come on together;

3.  Press the 

 button (B2) to set the actual water hardness 

(as measured by the indicator paper - see table in previous 
section).

4.  Press the 

 /

 button (B9) to confirm the selection.

The machine is now reprogrammed with the new water hard-
ness setting.

19.  TECHNICAL DATA

Voltage:  

220-240 V~ 50/60 Hz max. 10A

Absorbed power:  

1450W

Pressure:  

1.5MPa (15 bars)

Max. water tank capacity:  

1.8 l

Size LxDxH:  

240x440x360 mm

Cord length: 

1150 mm

Weight:  

9.2  kg

Max. beans container capacity: 

250 g

Summary of Contents for 132213166














Reviews: