Dell XPS 8920 Service Manual Download

Page: 34 / 102

Removing the secondary hard-drive

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

CAUTION:

Hard drives are fragile. Exercise care when handling the hard drive.

CAUTION:

To avoid data loss, do not remove the hard drive while the computer is in sleep or on state.

Prerequisites

Remove the

right-side cover

Procedure

1. Disconnect the data and power cables from the hard drive.
2. Remove the screws that secure the hard-drive cage to chassis.

1. #6-32 X 1/4'' screws (2)

2. hard drive

3. hard-drive cage

4. power cable

5. data cable

3. Lift the hard drive cage off the chassis.

Removing the secondary hard-drive

Summary of Contents for XPS 8920







































































































Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands

Dell XPS 8920, Service Manual

Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands