background image

10

Dell Networking W-IAP228 Wireless Instant Access Point

| Installation Guide

Safety and Regulatory Compliance

Regulatory Model Name

The regulatory model name of W-IAP228 Instant access point is APIN0228.

FCC

This device is electronically labeled and the FCC ID is displayed via the WebUI under the 

About

 menu. 

FCC Class B Part 15

This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is 
subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 
15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the manufacturer’s instructions, may cause interference harmful to radio 
communications.

If this equipment does cause interference, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio or TV technician for help.

EU Regulatory Conformance 

Dell, hereby declares that the APIN0228 device model is in compliance with the essential 

requirements and other relevant provisions of Directive 1999/5/EC -CE(!). The Declaration of Conformity made 
under Directive 1999/5/EC is available for viewing on 

dell.com.

Proper Disposal of Dell Equipment

For the most current information about Global Environmental Compliance and Dell products, visit 

dell.com

.

NOTE:  For country specific restrictions and additional safety and regulatory information, refer to the 

Dell Networking W-Series 

Safety, Environmental, and Regulatory Information

 document included with this product.

CAUTION:  Dell access points must be installed by a professional installer. The professional installer is responsible for ensuring 
that grounding is available and it meets applicable local and national electrical codes.

CAUTION:  RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment 
should be installed and operated with a minimum distance of 9.84 inches (25 cm) between the radiator and your body for 2.4 GHz 
and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 

CAUTION:  Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the 
user’s authority to operate this equipment.

Summary of Contents for W-IAP228

















Reviews: