Dell Vostro 3555 Owner'S Manual Download Page 83

Page: 83 / 116

Installing The Display Brackets, Hinges and Panel

1. Tighten the screws to secure the display brackets and hinges to the display

panel.

2. Affix the display cable to the back of the display panel
3. Secure the cables through the left hinge.
4. Tighten the screws to secure the display brackets and hinges to the display

assembly.

5. Secure the antenna cable to the right hinge.
6. Install the

display camera

7. Install the

display bezel

8. Install the

display assembly

9. Install the

palm rest

10. Install the

WWAN card

11. Install the

keyboard

12. Install the

hard drive

13. Install the

WLAN card

14. Install the

access panel

15. Install the

memory card

16. Install the

battery

17. Follow the procedures in

After Working Inside Your Computer

Summary of Contents for Vostro 3555





















































































































Search results

Summary of Contents for Vostro 3555

Reviews:

Related manuals for Vostro 3555

Brands by name

Popular brands

Dell Vostro 3555, Owner'S Manual

Search results

Summary of Contents for Vostro 3555

Reviews:

Related manuals for Vostro 3555

Brands by name

Popular brands