Dell Vostro 3555 Owner'S Manual Download Page 100

Page: 100 / 116

eSATA Device

Displays information about the installed

eSATA device.

AC Adapter Type

Displays the type of the AC adapter.

Advanced

Intel SpeedStep

Enable or disable the Intel

SpeedStep feature.

Default: Enabled

Virtualization

Enable or disable the Intel

Virtualization feature.

Default: Enabled

Integrated NIC

Enable or disable the power

supply to the on–board

network card.

Default: Enabled

USB Emulation

Enable or disable the USB

emulation feature

Default: Enabled

USB Powershare

Allows the computer to

charge external devices

using the stored system

battery power through the

USB PowerShare port,

even while the computer is

turned off.

Default: Enabled

USB Wake Support

Allows USB devices to

wake-up the computer from

standby. This feature is

enabled only when the AC

adapter is connected.

Default: Disabled

SATA Operation

Change the SATA controller

mode to either ATA or

AHCI.

Default: AHCI

Adapter Warnings

Enables or disables adapter

warnings.

Default: Enabled

Function Key Behavior

Specifies the behavior of

the function key <Fn> .

Default: Function key first

Charger Behavior

Specifies if the computer

battery will be charged

when connected to an AC

power source.

Default: Enabled

100

Summary of Contents for Vostro 3555





















































































































Search results

Summary of Contents for Vostro 3555

Reviews:

Related manuals for Vostro 3555

Brands by name

Popular brands

Dell Vostro 3555, Owner'S Manual

Search results

Summary of Contents for Vostro 3555

Reviews:

Related manuals for Vostro 3555

Brands by name

Popular brands