Dell Studio 1569 Service Manual Download Page 46

Page: 46 / 47

USB/Audio Board

Dell™ Studio™ 1569 Service Manual

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the
Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

Removing the USB/Audio Board

Follow the procedures in

Before You Begin

Remove the battery (see

Removing the Battery

Remove the power button panel (see

Removing the Power Button Panel

Remove the keyboard (see

Removing the Keyboard

Remove the palm rest (see

Removing the Palm Rest

Disconnect the speaker cable from the USB/audio board connector.

Pull the pull-tab to disconnect the USB cable from the USB/audio board connector.

Lift the connector latch, then pull the pull-tab and disconnect the audio cable from the USB/audio board connector.

Remove the three screws that secure the USB/audio board to the computer base.

10.

Lift the USB/audio board out of the computer base.

CAUTION:

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™

is not covered by your warranty.

CAUTION:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal

surface.

CAUTION:

To help prevent damage to the system board, remove the main battery (see

Removing the Battery

) before working inside the

computer.

USB cable

pull-tab

speaker cable

screws (3)

USB/audio board

audio cable

pull-tab

latch connector

Summary of Contents for Studio 1569
















































Search results

Summary of Contents for Studio 1569

Reviews:

Related manuals for Studio 1569

Brands by name

Popular brands

Dell Studio 1569, Service Manual

Search results

Summary of Contents for Studio 1569

Reviews:

Related manuals for Studio 1569

Brands by name

Popular brands