manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

IPv6 Basics

IPv6 basic commands are supported on the Dell Networking OS.

NOTE: 

For information about the Dell Networking OS version and platform that supports IPv6 in each software feature, see the 

IPv6 Addressing

 section in the 

Dell Networking OS Configuration Guide

.

 

Topics:

•

cam-ipv6 extended-prefix

•

clear ipv6 route

•

maximum dynamic-routes-ipv6

•

show cam-ipv6 extended-prefix

•

ipv6 unicast-host-route

•

ipv6 nd disable-reachable-timer

•

ipv6 nd dns-server 

•

ipv6 route

•

show ipv6 route

cam-ipv6 extended-prefix

Enable LPM partitioning to support IPv6 /65 to /128 route prefixes to be stored in Partition 1.

Syntax

cam-ipv6 extended-prefix 

<Max-IPv6-prefixes>

To remove LPM partitioning configuration, use no cam-ipv6 extended-prefix.

Parameters

Max-IPv6-Prefix

Maximum number of IPv6 prefixes in the mask length of /65 to /128. The possible values 
are 1024, 2048, and 3072.

Defaults

LPM is not partitioned with Partition 1 and therefore /65 to /128 prefixes are not converted to /64 prefixes and are 
installed and saved in LPM. All the packets for those routes traverse through the default route path.

Command Modes

CONFIGURATION

Command History

Version

Description

9.10(0.1)

Introduced on the S6010-ON and S4048T-ON.

9.10(0.0)

Introduced on the S6100–ON.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048–ON.

23

IPv6 Basics

813

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

3Com NBX 100 Release Note preview
NBX 100
Brand: 3Com Pages: 8
CyberData 4-Port PoweredUSB 2.0 Hub 011006 Quick Reference Manual preview
4-Port PoweredUSB 2.0 Hub 011006
Brand: CyberData Pages: 4
Patton electronics SmartNode 4658 Series Quick Start Manual preview
SmartNode 4658 Series
Brand: Patton electronics Pages: 12
Setra Systems SSC-2S Operation And Installation Instructions preview
SSC-2S
Brand: Setra Systems Pages: 4
Niles VSA-5 Owner'S Manual preview
VSA-5
Brand: Niles Pages: 7
Dahua PFS4226-24ET-240 User Manual preview
PFS4226-24ET-240
Brand: Dahua Pages: 3
A-Neuvideo ANI-MINI601HD Instruction Manual preview
ANI-MINI601HD
Brand: A-Neuvideo Pages: 15
EtherWAN EX24000 User Manual preview
EX24000
Brand: EtherWAN Pages: 239
M-E CUVEO CT-W2 Manual preview
CUVEO CT-W2
Brand: M-E Pages: 36
Kramer VP-26 User Manual preview
VP-26
Brand: Kramer Pages: 46
Kramer VS-121HC User Manual preview
VS-121HC
Brand: Kramer Pages: 33
SOFLY HDSW4 User Manual preview
HDSW4
Brand: SOFLY Pages: 4
Audioplex INW-8 Installation Manual preview
INW-8
Brand: Audioplex Pages: 8
Danfoss RT 30AW Installation Manual preview
RT 30AW
Brand: Danfoss Pages: 2
Wyrestorm MXV-0408-H2A v2 Quick Start Manual preview
MXV-0408-H2A v2
Brand: Wyrestorm Pages: 4
Blaze B.One Quick Start Manual preview
B.One
Brand: Blaze Pages: 18
CYP CDPS-U2HPIP Operation Manual preview
CDPS-U2HPIP
Brand: CYP Pages: 88
Elko inels RFSA-61M/MI/230V Quick Start Manual preview
inels RFSA-61M/MI/230V
Brand: Elko Pages: 7

Brands by name

Popular brands

Load more brands