manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

show cam-ipv6 extended-prefix

Display the current settings and next-boot settings for cam-ipv6 extended-prefix configuration. Display the cam-ipv6 extended-prefix

 

configuration.

Syntax

show cam-ipv6 extended-prefix

Defaults

None

Command Modes

EXEC

EXEC 

Privilege

Command History

Version

Description

9.10(0.0)

Introduced on the S6100–ON.

9.8(1.0)

Introduced on the Z9100–ON.

9.7(0.0)

Introduced on the S6000-ON.

9.5(0.1)

Introduced on the Z9500.

9.3(0.1)

Introduced on the S6000.

Usage Information

You can use this command to view the number of supported extended prefix entries in LPM configured. The 
output also displays the current applied value and the new value that is applicable after the reboot of the device.

Example

Dell# show cam-ipv6 extended-prefix

Cam-Ipv6-LPM Extended Prefix

--------------------------------

Current Settings

cam-ipv6-max-/65-to-/128-Prefix : 2048

Dell(conf)#

ipv6 unicast-host-route

Enable programming of IPv6 /128 route prefixes in L3 host table.

Syntax

[no] ipv6 unicast-host-route

Defaults

Enabled by default. By default, all the IPv6/128 route prefixes are installed only in L3 host table.

Command Modes

CONFIGURATION

Command History

Version

Description

9.10(0.0)

Introduced on the S6100–ON.

816

IPv6 Basics

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

IBM E12 Quick Installation Manual preview
E12
Brand: IBM Pages: 2
IDK MSD-804FD Series Command Manual preview
MSD-804FD Series
Brand: IDK Pages: 133
IDK MSD-72 Series User Manual preview
MSD-72 Series
Brand: IDK Pages: 150
IDK MSD-501 Command Reference Manual preview
MSD-501
Brand: IDK Pages: 101
IDK MSD-402 Command Reference Manual preview
MSD-402
Brand: IDK Pages: 85
IDK IMP-400UHD Command Reference Manual preview
IMP-400UHD
Brand: IDK Pages: 40
IDK FDX-32 User Manual preview
FDX-32
Brand: IDK Pages: 97
IDK FDX-S Series User Manual preview
FDX-S Series
Brand: IDK Pages: 117
IDK FDX-16 User Manual preview
FDX-16
Brand: IDK Pages: 77
KanexPro MX-HDBT8X818G Manual preview
MX-HDBT8X818G
Brand: KanexPro Pages: 16
Abtus MAX-USB44P Manual preview
MAX-USB44P
Brand: Abtus Pages: 15
SMSC LAN9312 Datasheet preview
LAN9312
Brand: SMSC Pages: 458
NETGEAR M4200 Series Installation Manual preview
M4200 Series
Brand: NETGEAR Pages: 2
NTI UNIMUX-nXm-UHD Installation And Operation Manual preview
UNIMUX-nXm-UHD
Brand: NTI Pages: 69
DirectConnect 43136 User Manual preview
43136
Brand: DirectConnect Pages: 10
Phonocar 5-981 Mounting Instructions preview
5-981
Brand: Phonocar Pages: 2
Milestone pro MP-SU21T-KVM User Manual preview
MP-SU21T-KVM
Brand: Milestone pro Pages: 32
Metra Electronics CS-HDM3X1SW3 User Manual preview
CS-HDM3X1SW3
Brand: Metra Electronics Pages: 8

Brands by name

Popular brands

Load more brands