Dell S5448F-ON Installation Manual Download Page 50

Page: 50 / 56

Specifications

This section lists the S5448F-ON switch specifications.

CAUTION:

Operate the product at an ambient temperature not higher than 45°C (113°F).

NOTE:

For RoHS information, see

Restricted Material Compliance

Topics:

•

Chassis physical design

•

IEEE standards

•

Agency compliance

•

USA Federal Communications Commission statement

•

European Union EMC directive conformance statement

•

India

•

Japan VCCI compliance for class A equipment

•

Safety standards and compliance agency certifications

•

Electromagnetic compatibility

•

Product recycling and disposal

Chassis physical design

Table 6. Chassis physical design

Parameter

Specifications

Height

43 mm (1.693 in)

Width

438.5 mm (17.26 in)

Depth

550 mm (21.65 in)

●

PSU handle 29.3 mm (1.15 in)

●

PSU latch 34.6 mm (1.37 in)

●

Fan tray handle 25.0 mm (0.99 in)

Chassis weight with factory-installed components

●

11.67 kg (2 PSUs and 6 fans)

●

25.73 lbs (2 PSUs and 6 fans)

Rack clearance required

●

Front: 12.7 cm (5 inches)

●

Back: 12.7 cm (5 inches)

Table 7. Environmental parameters

Parameter

Specifications

Operating temperature

●

0°C to 45°C (32°F to 113°F) continuously

●

-5°C to 45°C (23°F to 113°F) short term

●

Short term is </= 1% of operational hours per year.

NOTE:

Reduce maximum temperature by 1°C/125 meters

(1°F/228 feet) above 950 meters (3,117 feet).

Operating humidity

5% to 90% (RH), noncondensing

Storage temperature

-40°C to 70°C (-40°F to 158°F )

Specifications

Summary of Contents for S5448F-ON

























































Search results

Summary of Contents for S5448F-ON

Reviews:

Related manuals for S5448F-ON

Brands by name

Popular brands

Dell S5448F-ON, Installation Manual

Search results

Summary of Contents for S5448F-ON

Reviews:

Related manuals for S5448F-ON

Brands by name

Popular brands