manualshive.com logo in svg

Dell S3048-ON, Configuration Manual

The Dell S3048-ON Configuration Manual is a comprehensive user guide that assists in setting up and customizing your Dell S3048-ON networking switch. It is available for free download at manualshive.com, providing step-by-step instructions and valuable insights to maximize the performance of this advanced networking product.

Share
Download
background image

Bidirectional Forwarding Detection (BFD)

BFD is a protocol that is used to rapidly detect communication failures between two adjacent systems. It is a simple and lightweight 
replacement for existing routing protocol link state detection mechanisms. It also provides a failure detection solution for links on which no 
routing protocol is used.

BFD is a simple hello mechanism. Two neighboring systems running BFD establish a session using a three-way handshake. After the session 
has been established, the systems exchange periodic control packets at sub-second intervals. If a system does not receive a hello packet 
within a specified amount of time, routing protocols are notified that the forwarding path is down.

BFD provides forwarding path failure detection times on the order of milliseconds rather than seconds as with conventional routing protocol 
hellos. It is independent of routing protocols, and as such, provides a consistent method of failure detection when used across a network. 
Networks converge faster because BFD triggers link state changes in the routing protocol sooner and more consistently because BFD 
eliminates the use of multiple protocol-dependent timers and methods.

BFD also carries less overhead than routing protocol hello mechanisms. Control packets can be encapsulated in any form that is convenient, 
and, on Dell Networking routers, BFD agents maintain sessions that reside on the line card, which frees resources on the route processor. 
Only session state changes are reported to the BFD Manager (on the route processor), which in turn notifies the routing protocols that are 
registered with it.

BFD is an independent and generic protocol, which all media, topologies, and routing protocols can support using any encapsulation. Dell 
Networking has implemented BFD at Layer 3 and with user datagram protocol (UDP) encapsulation. BFD is supported on static routing 
protocols and dynamic routing protocols such as VRRP, OSPF, OSPFv3, IS-IS, and BGP.

 

Topics:

•

How BFD Works

•

Important Points to Remember

•

Configure BFD

How BFD Works

Two neighboring systems running BFD establish a session using a three-way handshake.
After the session has been established, the systems exchange control packets at agreed upon intervals. In addition, systems send a control 
packet anytime there is a state change or change in a session parameter. These control packets are sent without regard to transmit and 
receive intervals.

NOTE: 

The Dell Networking Operating System (OS) does not support multi-hop BFD sessions.

If a system does not receive a control packet within an agreed-upon amount of time, the BFD agent changes the session state to Down. It 
then notifies the BFD manager of the change and sends a control packet to the neighbor that indicates the state change (though it might 
not be received if the link or receiving interface is faulty). The BFD manager notifies the routing protocols that are registered with it 
(clients) that the forwarding path is down and a link state change is triggered in all protocols.

NOTE: 

A session state change from Up to Down is the only state change that triggers a link state change in the routing protocol 

client.

8

138

Bidirectional Forwarding Detection (BFD)

Summary of Contents for S3048-ON













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S3048-ON

3Com SuperStack II Important Information preview
SuperStack II
Brand: 3Com Pages: 2
3Com CoreBuilder 5000 Quick Start And Reference preview
CoreBuilder 5000
Brand: 3Com Pages: 16
3Com CoreBuilder 9000 Quick Installation Manual preview
CoreBuilder 9000
Brand: 3Com Pages: 24
3Com 4210 Series Datasheet preview
4210 Series
Brand: 3Com Pages: 8
3Com PathBuilder S200 Series Feature Manual preview
PathBuilder S200 Series
Brand: 3Com Pages: 11
3Com 4400 Datasheet preview
4400
Brand: 3Com Pages: 8
3Com CoreBuilder 3500 Getting Started Manual preview
CoreBuilder 3500
Brand: 3Com Pages: 96
StarTech.com SV431DHD4KU User Manual preview
SV431DHD4KU
Brand: StarTech.com Pages: 24
Cabletron Systems 9F426-03 Appendix preview
9F426-03
Brand: Cabletron Systems Pages: 14
Taiden TMX-0404SDI Installation And Operation Manual preview
TMX-0404SDI
Brand: Taiden Pages: 21
EtherWAN EX17162A Installation Manual preview
EX17162A
Brand: EtherWAN Pages: 2
EtherWAN EX19164A Installation Manual preview
EX19164A
Brand: EtherWAN Pages: 2
Black Box KV1044A-R2 Specifications preview
KV1044A-R2
Brand: Black Box Pages: 4
Minicom DX DX 432 Operating Manual preview
DX 432
Brand: Minicom DX Pages: 36
Inter-m PX-6116 Operation Manual preview
PX-6116
Brand: Inter-m Pages: 12
ATEN Master View CS-74A User Manual preview
Master View CS-74A
Brand: ATEN Pages: 16
EtherWAN EX24000 User Manual preview
EX24000
Brand: EtherWAN Pages: 239
Voith BTS-Ex Installation And Operating Manual preview
BTS-Ex
Brand: Voith Pages: 98

Brands by name

Popular brands

Load more brands