Dell PowerVault LTO User Manual Download Page 8

Page: 8 / 76

a80hd001

Figure 2. Tape drive external model

a77ug279

Figure 3. Tape drive rack mount model

Serial Attached SCSI (SAS) interface

A drive with a SAS (Serial Attached SCSI) interface can be linked directly to controllers. The SAS interface

offers the following advantages over the traditional SCSI interface.
• SAS enables multiple devices (up to 128) of different sizes and types to be connected simultaneously

with thinner and longer cables.

• Offers full-duplex signal transmission.
• SAS drives can be hot-plugged.

Specifications and features

Specifications

Table 1. Drive information and performance specification
Generation

LTO 9

LTO 8

LTO 7

LTO 6

LTO 5

Inquiry

ULT3580-HH9

ULTRIUM-HH9

ULT3580-HH8

ULTRIUM-HH8

ULT3580-HH7

ULTRIUM-HH7

ULT3580-HH6

ULTRIUM-HH6

ULT3580-HH5

ULTRIUM-HH5

Interface

(speed)

FC (8 Gb)

SAS (12 Gb)

FC (8 Gb)

SAS (6 Gb)

FC (8 Gb)

SAS (6 Gb)

FC (8 Gb)

SAS (6 Gb)

FC (8 Gb)

SAS (6 Gb)

2 Dell PowerVault LTO Tape Drive: User's Guide

Summary of Contents for PowerVault LTO













































































Search results

Summary of Contents for PowerVault LTO

Reviews:

Related manuals for PowerVault LTO

Brands by name

Popular brands

Dell PowerVault LTO, User Manual

Search results

Summary of Contents for PowerVault LTO

Reviews:

Related manuals for PowerVault LTO

Brands by name

Popular brands