background image

v

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help 
protect your server, storage system, or appliance from potential damage. For com-
plete safety, regulatory, and warranty information, refer to your system’s 

System 

Information 

document.

Notes, Notices, Cautions, and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in 
bold type or in italic type. These blocks are notes, notices, cautions, and warnings, 
and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of 
your computer system.

NOTICE: A NOTICE indicates either potential damage to hardware or loss 
of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potentially hazardous situation which, if 
not avoided, may result in minor or moderate injury.

WARNING: A WARNING indicates a potentially hazardous situation which, 
if not avoided, could result in death or serious bodily injury.

Precautions for Rack-Mountable Products

Observe the following precautions for rack stability and safety. Also refer to the rack 
installation documentation accompanying the system and the rack for specific warn-
ing and/or caution statements and procedures.

Servers, storage systems, and appliances are considered to be components in a rack. 
Thus, “component” refers to any server, storage system, or appliance, as well as to 
various peripherals or supporting hardware.

WARNING: Installing Dell system components in a Dell rack without the 
front and side stabilizers installed could cause the rack to tip over, poten-
tially resulting in bodily injury under certain circumstances. Therefore, 
always install the stabilizers before installing components in the rack.

2D786bk0.book  Page v  Thursday, January 18, 2001  8:44 PM

Summary of Contents for PowerEdge 350

































Reviews: