manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 51

Figure 17: 48-port RJ-45 Line Card

The line card has two status LEDs labeled ON and ST on the faceplate that indicate the
online and status information for the line card. See “Line Card LEDs in a J-EX8200 Switch”
on page 35.

Related

Documentation

8-port SFP+ Line Card in a J-EX8200 Switch on page 32

•

•

48-port SFP Line Card in a J-EX8200 Switch on page 33

•

Installing a Line Card in a J-EX8200 Switch on page 123

•

Handling and Storing Line Cards in J-EX8200 Switches on page 175

Line Card LEDs in a J-EX8200 Switch

The line cards in J-EX8200 switches have two status LEDs labeled ON and ST on the
faceplate (see Figure 18 on page 35, Figure 19 on page 35, and Figure 20 on page 36) that
indicate the online and status information of the line cards.

Figure 18: Status LEDs on 8-port SFP+ Line Card

Figure 19: Status LEDs on 48-port SFP Line Card

35

Chapter 2: Component Descriptions

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands