manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 139

•

Ensure that you know how to handle and store the line card (see “Handling and Storing
Line Cards in J-EX8200 Switches” on page 175).

To unpack a line card (see Figure 52 on page 123):

1.

Move the shipping carton to a staging area as close to the installation site as possible.

2.

Position the carton so that the arrows are pointing up.

3.

Open the top flaps on the shipping carton.

4.

Pull out the packing material, which holds the line card in place.

5.

Remove the line card from the antistatic bag.

6.

Save the shipping carton and packing materials in case you need to move or ship the
line card later.

Figure 52: Unpacking a Line Card Used in a J-EX8200 Switch

Related

Documentation

Packing a Line Card Used in a J-EX8200 Switch on page 197

•

•

Installing a Line Card in a J-EX8200 Switch on page 123

•

8-port SFP+ Line Card in a J-EX8200 Switch on page 32

•

48-port SFP Line Card in a J-EX8200 Switch on page 33

•

48-port RJ-45 Line Card in a J-EX8200 Switch on page 34

Installing a Line Card in a J-EX8200 Switch

J-EX8200 switches have field-replaceable unit (FRU) line cards that can be installed in
the line card slots on the front of the switch chassis. The line cards are hot-insertable
and hot-removable: You can remove and replace them without powering off the switch
or disrupting switch functions.

Before you begin installing a line card in the switch:

123

Chapter 9: Installing Switch Components

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands