Dell PowerConnect J-8216 Hardware Manual Download Page 173

Page: 173 / 270

CHAPTER 13

Removing Switch Components

•

Removing an AC Power Supply from a J-EX8200 Switch on page 157

•

Removing a Fan Tray from a J-EX8216 Switch on page 159

•

Taking the RE Module Offline in a J-EX8216 Switch on page 161

•

Removing an RE Module from a J-EX8216 Switch on page 163

•

Taking the SF Module Offline in a J-EX8216 Switch on page 164

•

Removing an SF Module from a J-EX8216 Switch on page 165

•

Removing a Line Card from a J-EX8200 Switch on page 166

•

Removing a Transceiver from a J-EX Series Switch on page 168

•

Disconnecting a Fiber-Optic Cable from a J-EX Series Switch on page 170

•

Removing the Power Cord Tray from a Rack or Cabinet for a J-EX8200
Switch on page 171

Removing an AC Power Supply from a J-EX8200 Switch

The AC power supply in a J-EX8200 switch is a hot-removable and hot-insertable
field-replaceable unit (FRU). You remove AC power supplies from the front of the chassis.

CAUTION:

Before you remove a power supply, ensure that you have power

supplies sufficient to power the switch left in the chassis. See “Calculating
Power Requirements for a J-EX8216 Switch” on page 85.

Before you remove an AC power supply from the switch:

•

Ensure you understand how to prevent ESD damage. See “Prevention of Electrostatic
Discharge Damage on J-EX Series Switches” on page 230.

Ensure that you have the following parts and tools available to remove an AC power
supply from a J-EX8200 switch chassis:

•

Electrostatic discharge (ESD) grounding strap

•

Phillips (+) screwdriver, number 1

•

Replacement power supply or a cover panel for the power supply slot

157

Summary of Contents for PowerConnect J-8216















































































































































































































































































Search results

Summary of Contents for PowerConnect J-8216

Reviews:

Brands by name

Popular brands

Dell PowerConnect J-8216, Hardware Manual

Search results

Summary of Contents for PowerConnect J-8216

Reviews:

Brands by name

Popular brands