manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 101

CAUTION:

AC power cords for J-EX8200 switches are intended for use with

this switch only and not for any other use.

Power Cable Warning (Japanese)

WARNING: The attached power cable is only for this product. Do not use the cable for another product.

CAUTION:

Power cords must not block access to switch components. We

recommend that you route all AC power cord cables through the power cord
tray provided with the switch.

WARNING:

The switch is pluggable type A equipment installed in a

restricted-access location. It has a separate protective earthing terminal
provided on the chassis in addition to the grounding pin of the power supply
cord. This separate protective earth terminal must be permanently connected
to earth ground. See “Connecting Earth Ground to a J-EX Series Switch” on
page 129.

Related

Documentation

AC Power Supply in a J-EX8200 Switch on page 39

•

•

AC Power Electrical Safety Guidelines for J-EX Series Switches on page 232

•

AC Power Disconnection Warning for J-EX Series Switches on page 233

•

General Electrical Safety Guidelines and Warnings for J-EX Series Switches on page 229

•

Connecting AC Power to a J-EX8200 Switch on page 131

Calculating Power Requirements for a J-EX8216 Switch

Use the information in this topic to calculate power consumption, system thermal output,
and number of power supplies required for different J-EX8216 switch configurations.

Before you begin these calculations:

•

Ensure you understand the different switch configurations. See “J-EX8216 Switch
Configurations” on page 7.

85

Chapter 7: Planning Power Requirements

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands