manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 151

NOTE:

After you power on a power supply, wait for at least 60 seconds before

you turn it off. After you power off a power supply, wait for at least 60 seconds
before you turn it back on.

If the system is completely powered off when you switch on a power supply,
the SRE or RE module boots as the power supply completes its startup
sequence.

After you power on a power supply, it can take up to 60 seconds for status
indicators such as power supply LEDs and the

show chassis

operational mode

CLI command display to indicate that the power supply is functioning
normally. Ignore any error indicators that might appear during the first 60
seconds.

Related

Documentation

Installing an AC Power Supply in a J-EX8200 Switch on page 114

•

•

Connecting AC Power to a J-EX8200 Switch on page 131

•

Powering Off a J-EX8200 Switch on page 151

Connecting a J-EX Series Switch to a Network for Out-of-Band Management

You can monitor and manage a J-EX Series switch using a dedicated management
channel. J-EX Series switches have a management port with an RJ-45 connector for
out-of-band management. Use the management port to connect the J-EX Series switch
to the management device.

Ensure that you have an Ethernet cable with an RJ-45 connector available. One such
cable is provided with the switch. Figure 61 on page 135 shows the RJ-45 connector of the
Ethernet cable supplied with the switch.

Figure 61: Ethernet Cable Connector

To connect a J-EX Series switch to a network for out-of-band management (see Figure
62 on page 136):

1.

Connect one end of the Ethernet cable to the management port (labeled

MGMT

) on

the J-EX Series switch.

For the location of the

MGMT

port, see “Routing Engine (RE) Module in a J-EX8216

Switch” on page 26.

2.

Connect the other end of the Ethernet cable to the management device.

135

Chapter 10: Connecting the Switch

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands