manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 152

Figure 62: Connecting a J-EX Series Switch to a Network for Out-of-Band
Management

Related

Documentation

Connecting a J-EX Series Switch to a Management Console on page 136

•

•

Management Port Connector Pinout Information for a J-EX8200 Switch on page 50

•

Cables Connecting the J-EX8200 Switch to Management Devices on page 77

Connecting a J-EX Series Switch to a Management Console

You can configure and manage a J-EX Series switch using a dedicated console. Every
J-EX Series switch has a console port with an RJ-45 connector. Use the console port to
connect the J-EX Series switch to the management console or to a console server. The
console port accepts a cable with an RJ-45 connector.

Ensure that you have an Ethernet cable with an RJ-45 connector available. An RJ-45
cable and an RJ-45 to DB-9 serial port adapter are supplied with the switch.

Figure 63 on page 136 shows the RJ-45 connector of the Ethernet cable supplied with the
switch.

Figure 63: Ethernet Cable Connector

NOTE:

If your laptop or PC does not have a DB-9 male connector pin and you

want to connect your laptop or PC directly to a J-EX Series switch, use a
combination of the RJ-45 to DB-9 female adapter supplied with the switch
and a USB to DB-9 male adapter. You must provide the USB to DB-9 male
adapter.

136

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands