Dell PowerConnect B-8000 Hardware Reference Manual Download | Manualshive

Page: 37 / 58

background image

PowerConnect B-8000 Hardware Reference Manual

25

53-1001788-01

Chapter

4

Removal and Replacement Procedures (RRPs)

In this chapter

•

RRP: Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

•

RRP: Fan assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Introduction

NOTE

Read the

“Installation and safety considerations”

before servicing.

The field replaceable units (FRUs) in the Powerconnect B-8000 can be removed and replaced
without special tools. The PowerConnect B-8000 can continue operating during many of the FRU
replacements if the conditions specified in the procedure are followed.

The following sections contain FRU removal and replacement procedures (RRPs).

RRP: Power supply

The PowerConnect B-8000 has two power supplies, as displayed in

. Fabric OS identifies

the power supplies from right to left on the non-port side as power supply 1 and power supply 2.
(The actual appearance of the PowerConnect B-8000 may differ from this illustration but the
locations are correct.)

FIGURE 6

Switch power supplies on the non-port side

CAUTION

Disassembling any part of the power supply voids the part warranty and regulatory certifications.
There are no user-serviceable parts inside the power supply. The cooling system relies on
pressurized air, do not leave either of the power supply slots empty longer than two minutes when

1

Power supply 1

2

Power supply 2

1

2

«
...
35
36
37
38
39
...
»

Summary of Contents for PowerConnect B-8000



























































Reviews:

No comments

Related manuals for PowerConnect B-8000

Brand: Magnetrol Pages: 12

Brand: Magnetrol Pages: 24

Brand: IDEC Pages: 5

Brand: IDEC Pages: 7

Brand: IBM Pages: 166

Brand: Lantronix Pages: 2

Brand: SMC Networks Pages: 102

Brand: Edge-Core Pages: 12

3C16710 - OfficeConnect 8/TPM Hub

Brand: 3Com Pages: 130

AMX ENOVA DVX-3250HD-SP

Brand: Harman Pages: 119

Brand: Gomax Pages: 24

Brand: N-Tron Pages: 15

Cutler-Hammer RTHMFDA20100WSU

Brand: Eaton Pages: 28

Brand: Little Giant Pages: 8

Brand: HighSecLabs Pages: 10

Brand: Marmitek Pages: 32

Brand: Blackberry Pages: 10

Brand: Omron Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands