Dell OptiPlex E1, Reference And Installation Manual, Page: 50 / 158

2-16 Dell OptiPlex E1 Managed PC Reference and Installation Guide
8VLQJWKH6\VWHP3DVVZRUG)HDWXUH
&$87,21 7KH SDVVZRUG IHDWXUHV SURYLGH D EDVLF OHYHO RI VHFXULW\ IRU WKH
GDWD RQ \RXU V\VWHP +RZHYHU WKH\ DUH QRW IRROSURRI ,I \RXU GDWD UHTXLUHV
PRUH VHFXULW\ LW LV \RXU UHVSRQVLELOLW\ WR REWDLQ DQG XVH DGGLWLRQDO IRUPV RI
SURWHFWLRQ VXFK DV GDWD HQFU\SWLRQ SURJUDPV
Your Dell system is shipped to you without the system password feature enabled. If
system security is a concern, you should operate your system only with system
password protection.
You can assign a system password, as described in the next subsection, “Assigning a
System Password,” whenever you use the System Setup program. After a system
password is assigned, only those who know the password have full use of the
system.
When the System Password category is set to Enabled, the computer system
prompts you for the system password just after the system boots.
To change an existing system password, you must know the password (see “Deleting
or Changing an Existing System Password” found later in this section). If you assign
and later
forget a system password, you must remove the computer cover to
change a jumper setting that disables the system password feature (see “Dis-
abling a Forgotten Password” found later in this chapter). Note that you erase the
setup password at the same time.
&$87,21 ,I \RX OHDYH \RXU V\VWHP UXQQLQJ DQG XQDWWHQGHG ZLWKRXW KDYLQJ
D V\VWHP SDVVZRUG DVVLJQHG RU LI \RX OHDYH \RXU FRPSXWHU XQORFNHG VR
WKDW VRPHRQH FDQ GLVDEOH WKH SDVVZRUG E\ FKDQJLQJ D MXPSHU VHWWLQJ DQ\
RQH FDQ DFFHVV WKH GDWD VWRUHG RQ \RXU KDUGGLVN GULYH
$VVLJQLQJD6\VWHP3DVVZRUG
Before you can assign a system password, you must enter the System Setup program
and check the System Password category.
When a system password is assigned, the System Password setting shown is
Enabled. When the system password feature is disabled by a jumper setting on the
system board, the option shown is Disabled by Jumper.
You cannot change or enter
a new system password if the Disabled by Jumper option is displayed. When a
system password is not assigned, the System Password
setting shown is Not
Enabled.
To assign a system password, follow these steps:
9HULI\ WKDW WKH 3DVVZRUG 6WDWXV VHWWLQJ LV VHW WR 8QORFNHG
For instructions on changing this setting, see “Password Status” found earlier in
this chapter.
+LJKOLJKW WKH 6\VWHP 6HFXULW\ VHWWLQJ DQG SUHVV (QWHU!
+LJKOLJKW WKH 6\VWHP 3DVVZRUG VHWWLQJ DQG SUHVV (QWHU!