Dell Networking S6000 System Reference Manual Download

Page: 910 / 1510

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.7.1.0

Introduced on the S-Series.

Version 7.6.1.0

Introduced on the C-Series and E-Series.

Related
Commands

protocol lldp (Configuration)

— enables LLDP globally.

debug lldp interface

— debugs LLDP.

show lldp neighbors

— displays the LLDP neighbors.

advertise med guest-voice-signaling

To advertise a separate limited voice service for a guest user when the guest voice control packets use a

separate network policy than the voice data, configure the system.

S6000

Syntax

advertise med guest-voice-signaling {

vlan-id layer2_priority

DSCP_value

} | {priority-tagged

number

}

To return to the default, use the

no advertise med guest-voice-signaling

{

vlan-id layer2_priority DSCP_value

} | {priority-tagged

number

}

command.

Parameters

vlan-id

Enter the VLAN ID. The range is from 1 to 4094.

layer2_priority

Enter the Layer 2 priority. The range is from 0 to 7.

DSCP_value

Enter the DSCP value. The range is from 0 to 63.

priority-tagged

number

Enter the keywords

priority-tagged

then the Layer 2

priority. The range is from 0 to 7.

Defaults

unconfigured.

Command
Modes

CONFIGURATION (conf-lldp)

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

910

Link Layer Discovery Protocol (LLDP)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands