Dell Networking S6000 System Reference Manual Download

Page: 642 / 1510

Parameters

number

Enter a number as the interface number. The range is from 0
to 16383.

Defaults

Not configured.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.4.1.0

Introduced

Example

Dell(conf)#interface loopback 1655

Dell(conf-if-lo-1655)#

Related
Commands

interface

— configures a physical interface.

interface null

— configures a Null interface.

interface port-channel

— configures a port channel.

interface vlan

— configures a VLAN.

interface ManagementEthernet

Configure the Management port on the system (either the Primary or Standby RPM).

S6000

Syntax

interface ManagementEthernet

slot/port

Parameters

slot/port

Enter the keyword

ManagementEthernet

, then the slot

number (0 or 1) and port number zero (0).

Defaults

Not configured.

642

Interfaces

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands