Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 383 / 1510

background image

Usage
Information

Peers that are enabled within a peer group are disabled when their peer group is
disabled.

The

neighbor shutdown

command terminates all BGP sessions on the BGP

neighbor or BGP peer group. Use this command with caution as it terminates the
specified BGP sessions. When a neighbor or peer group is shut down, use the

show

ip bgp summary

command to confirm its status.

Related
Commands

show ip bgp summary

— displays the current BGP configuration.

show ip bgp neighbors

— displays the current BGP neighbors.

neighbor soft-reconfiguration inbound

Enable soft-reconfiguration for BGP.

S6000

Syntax

neighbor {

ip-address

|

peer-group-name

} soft-reconfiguration

inbound

To disable, use the

no neighbor {

ip-address

|

peer-group-name

} soft-

reconfiguration inbound

command.

Parameters

ip-address

Enter the IP address of the neighbor in dotted decimal
format.

peer-group-
name

Enter the name of the peer group to disable or enable all
routers within the peer group.

Defaults

Disabled

Command
Modes

ROUTER BGP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Border Gateway Protocol

383

«
...
381
382
383
384
385
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: Pakedge Pages: 24

SmartSwitch 6500

Brand: Cabletron Systems Pages: 62

Brand: Eaton Pages: 40

Hub M50 Mesh Cube

Brand: Xunison Pages: 11

Brand: GALCO Pages: 22

Brand: GarrettCom Pages: 63

IES6200-PN-16T4GS-2P48

Brand: 3onedata Pages: 3

Cordex HP CXRF 48-2.4kW

Brand: Alpha Pages: 56

Brand: C&H Technologies Pages: 28

Brand: AT&T Pages: 24

Brand: Wyrestorm Pages: 2

Brand: H3C Pages: 39

Brand: Eneo Pages: 19

Brand: A-Neuvideo Pages: 9

Brand: Airlinkplus Pages: 2

Brand: Extron electronics Pages: 6

ePowerSwitch 8XM Master

Brand: ADDER Pages: 2

Brand: 3Com Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands