Dell Networking S6000 System Reference Manual Download

Page: 1388 / 1510

show storm-control unknown-unicast

Display the storm control unknown-unicast configuration.

S6000

Syntax

show storm-control unknown-unicast [

interface

]

Parameters

interface

(OPTIONAL) Enter one of the following interfaces to display
the interface specific storm control configuration:

• For a 1-Gigabit Ethernet interface, enter the keyword

GigabitEthernet

then y the slot/port information.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/ port information.

Defaults

none

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.2(0.0)

Introduced on the M I/O Aggregator. This command is
supported in Programmable-Mux (PMUX) mode only.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.5.1.0

Introduced on the E-Series.

1388

Storm Control

«
...
1386
1387
1388
1389
1390
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands