Dell Latitude E5510 Service Manual Download

Page: 67 / 76

Back to Contents Page

Technical Specifications

System Information

Memory

Audio

ExpressCard

Fingerprint Reader (Optional)

Display

Touchpad

AC Adapter

Environmental

Processor

Video

Communications

PC Card

Ports and Connectors

Keyboard

Battery

Physical

NOTE:

Offerings may vary by region. For more information regarding the configuration of your computer, click

Start

Help and Support

and select the

option to view information about your computer.

System Information

Chipset

Intel

HM55 Express Chipset

Data bus width

64 bits

DRAM bus width

dual-channel 64 bits

NOTE:

You must install memory in pairs for

dual-channel mode to work.

Processor

Types

Intel Core™ i3 series

Intel Core i5 series
Intel Core i7 series

Intel Celeron™

L2 cache

2 MB, 3 MB, and 4 MB

Memory

Type

DDR3 1333 MHz SDRAM
(operating at 1066 MHz)

Connectors

two SODIMM slots

Module capacities

1 GB, 2 GB, and 4 GB

Minimum memory

1 GB

Maximum memory

8 GB

NOTE:

Only 64-bit operating systems can detect

memory capacities greater than 4 GB.

Video

Type

Intel UMA video

Data bus

integrated video

Controller

Intel Graphics Media Accelerator HD

Output

15-pin video connector

Audio

Type

four channel high definition audio (HDA)codec

Controller

IDT 92HD81B

Stereo conversion

24-bit (analog-to-digital and digital-to-analog)

Interfaces

Internal

high definition audio bus

External

microphone-in/line-in connector and stereo

Speakers

two

Volume controls

volume up, volume down, and mute buttons

Communications

Modem

internal (optional)

Network adapter

10/100/1000 Mbps Broadcom NetXtreme 5761E

Summary of Contents for Latitude E5510













































































Search results

Summary of Contents for Latitude E5510

Reviews:

Related manuals for Latitude E5510

Brands by name

Popular brands

Dell Latitude E5510, Service Manual

Search results

Summary of Contents for Latitude E5510

Reviews:

Related manuals for Latitude E5510

Brands by name

Popular brands