background image

52

EMC VNXe3100 Hardware Information Guide

Overview

Specifications

Table 27

 lists the VNXe3100 platform physical specifications, operating environment, and 

power requirements.

Table 27  VNXe3100 platform specifications

Parameter

Characteristics

Dimensions (approximate)

Height

28 in. (71.12 cm) or 16 NEMA units (U) total; one disk 

processor enclosure (DPE, 2U) and seven disk-array enclosures 

(2U, 12 [3.5-inch] DAE)

Width

17.5 in. (44.5 cm); mounting bars fit standard 19-inch NEMA 

cabinets

Depth

Chassis to rear: 19.5 in. (49.53 cm)

Weight

424.5 lb (192.55 kg) total; one DPE and seven 2U, 12 (3.5-inch) 

DAEs

Operating environment

Temperature

50-104° F (10-40° C)

Temperature gradient

18° F/hr (10° C/hr)

Relative humidity

20% to 80% (non-condensing)

Altitude

8,000 ft (2,438 m) @ 104° F (40° C) max.
10,000 ft (3,048 m) @ 98.6° F (37° C) max.

AC power and dissipation

AC line voltage

100 to 240 VAC (47-63 Hz), single phase

AC line current

4.0 A max at 100 VAC, 2.0 A max at 200 VAC

1

2.5 A max at 100 VAC, 1.3 A max at 200 VAC

2

Power consumption

395 VA (380 W) max

a

250 VA (240 W) max

b

Power factor

0.98 min at full load, low voltage

Heat dissipation

1.37 x 10

6

 J/hr, (1,300 Btu/hr) max

a

8.46 x 10

5

 J/hr, (800 Btu/hr) max

b

AC protection

15 A fuse on each power supply, both phases

AC inlet type (receptacle)

IEC320-C14 appliance coupler (per power supply)

Ride-through

30 ms minimum at full load

Current sharing

± 15% of full load, between power supplies

1. DPE
2. DAE

Summary of Contents for EMC VNXe Series





















































Reviews: