Dell EMC VNXe Series Hardware Information Manual Download Page 12

Page: 12 / 52

EMC VNXe3100 Hardware Information Guide

Overview

Note: A fully configured dual SP VNXe3100 platform includes up to seven DAEs supporting
a maximum of from 96 to 99 disk drives depending on the type and mix of the DAEs used
(for configuration information, see

“DPE and DAE configuration rules” on page 37

Front view

Figure 2

shows an example of the front view of the VNXe3100 platform having a 2U, 12

(3.5-inch) disk drive DPE.

Figure 2 Example of a VNXe3100 platform with a 2U, 12 (3.5-inch) disk drive DPE (front view)

Rear view

Looking from left to right,

Figure 3

shows an example of the rear view of a VNXe3100

platform having a 2U DPE with a Cache Protection Module and a single storage processor
(SP A), respectively.

Figure 3 Example of a VNXe3100 2U DPE with a Cache Protection Module and a single SP,
respectively (rear view)

Looking from left to right,

Figure 4

shows an example of the rear view of a VNXe3100

platform having a 2U DPE with two storage processors (SP B and A), respectively.

Figure 4 Example of a VNXe3100 2U DPE with two SPs (rear view)

Installation

SAS 450 GB 15K RPM

VNX-000080

1 GBE

0 1

6Gb SAS
6Gb SAS

1
0

e0 e1

1 GbE

VNX-000088

1 GBE

0 1

6Gb SAS
6Gb SAS

1
0

e0 e1

1 GbE

1 GBE

0 1

6Gb SAS
6Gb SAS

1
0

e0 e1

1 GbE

VNX-000084

Summary of Contents for EMC VNXe Series





















































Search results

Summary of Contents for EMC VNXe Series

Reviews:

Related manuals for EMC VNXe Series

Brands by name

Popular brands

Dell EMC VNXe Series, Hardware Information Manual

Search results

Summary of Contents for EMC VNXe Series

Reviews:

Related manuals for EMC VNXe Series

Brands by name

Popular brands