background image

Upgrade Dell EMC Networking N3000E-ON Switches 

 

 

Page 9

 

4.

 

Activate 6.5.3.36 (Advanced) firmware on N3000E-ON switch. 

5.

 

Reload the switch. 

6.

 

Download the 6.5.3.36 firmware image (N3100Advv6.5.3.36.stk) to N3132PX-ON switch. 

 

NOTE:

 Activate the image to use as the boot (active) image after the switch 

resets. Images on the N3000E-ON switch is named as active and backup. 

 

7.

 

Activate 6.5.3.36 (Advanced) firmware on N3132PX-ON switch. 

8.

 

Reload the switch. 

9.

 

After switch reloaded, download and activate the mixed-stack firmware image 
(N3000N3100Advv6.5.3.36.itb) on N3000E-ON and N3132PX-ON switches. 

10.

 

Reload the switches again. 

11.

 

Power OFF both N3000E-ON and N3132PX-ON switches. Plug-in mini-SAS stack cables and form the 
stack between N3000E-ON and N3132PX-ON switches. 

12.

 

Power ON stack (N3000E-ON with N3132PX-ON). 

13.

 

Verify the stack of N3000E-ON and N3132PX-ON switches via 

show switch

 and 

show version

 command 

output like below: 

 

Console#show switch 

 

    Management Standby   Preconfig     Plugged-in    Switch        Code 
SW  Status     Status    Model ID      Model ID      Status        Version 
--- ---------- --------- ------------- ------------- ------------- ----------- 
1   Stack Mbr  Oper Stby N3132PX-ON    N3132PX-ON    OK            6.5.3.36 
2   Mgmt Sw              N3048EP-ON    N3048EP-ON    OK            6.5.3.36 

 
 

Console#show version 

 

Machine Description............... Dell EMC Networking Switch 
System Model ID................... N3048EP-ON 
Machine Type...................... Dell EMC Networking N3048EP-ON 
Serial Number..................... 
Manufacturer...................... 0xbc00 
Burned In MAC Address............. 0090.BC06.A571 
System Object ID.................. 1.3.6.1.4.1.674.10895.3060 
SOC Version....................... BCM56340_A0 
HW Version........................ 5 
CPLD Version...................... 20 
Image File........................ N3000Advv6.5.3.36 
Software Capability............... Stack Limit = 12, VLAN Limit = 4093 
 
unit active      backup      current-active next-active 
---- ----------- ----------- -------------- -------------- 
1    6.5.3.36     6.5.3.36        6.5.3.36       6.5.3.36 
2    6.5.3.36     6.5.3.36        6.5.3.36       6.5.3.36 

 
 
 
 

 

 

 

Summary of Contents for EMC PowerSwitch N3000E-ON Series






















Reviews: