Dell D29M Service Manual Download Page 67

Page: 67 / 86

4. Align the front I/O-bracket with the slots on the chassis.
5. Replace the two (#6-32) screws to secure the front I/O-bracket to the chassis.

Next steps

1. Install the

processor

2. Install the

processor fan and heat-sink assembly

3. Install the

4. Install the

5. Install the

6. Install the

7. Install the

8. Install the

9. Install the

10. Install the

11. Follow the procedure in

after working inside your computer

NOTE:

Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup

program after you replace the system board.

NOTE:

Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup

program. You must make the appropriate changes again after you replace the system board.

Removing and installing components

Summary of Contents for D29M























































































Search results

Summary of Contents for D29M

Reviews:

Related manuals for D29M

Brands by name

Popular brands

Dell D29M, Service Manual

Search results

Summary of Contents for D29M

Reviews:

Related manuals for D29M

Brands by name

Popular brands