manualshive.com logo in svg

Dell Alienware Area-51m R2, Service Manual, Page: 63 / 94

Share
Download
Dell Alienware Area-51m R2 Service Manual Download Page 63

About this task
The following image indicates the location of the graphics card and provides a visual representation of the installation procedure.

Steps
1. Place the graphics card on the system board and align the screw holes on the graphics card with the screw holes on the system

board.

2. Replace the three screws (M2x3) that secure the graphics card to the system board.
3. Replace the two screws (M2x3) that secure the two graphics-card cables to the graphics card.
4. Connect the graphics-card power cable to the graphics card.

Next steps
1. Install the 

heat-sink assembly

.

2. Install the 

computer base

.

3. Install the 

rear-I/O cover

.

4. Install the 

solid-state drive from M.2 slot four

, if applicable.

5. Install the 

solid-state drive from M.2 slot three

, if applicable.

6. Follow the procedure from step 5 to step 8 in 

Installing the hard drive

, if applicable.

7. Install the 

solid-state drive in M.2 slot one

.

8. Install the 

wireless card

.

9. Install the 

memory modules

.

10. Install the 

battery

.

11. Install the 

base cover

.

12. Follow the procedure in 

After working inside your computer

.

Left power-adapter port

Removing the left power-adapter port

Prerequisites
1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

base cover

.

3. Remove the 

battery

.

63

Summary of Contents for Alienware Area-51m R2































































































Reviews:

No comments