manualshive.com logo in svg

Dell 3WY51, Firmware Upgrading Instruction

Share
Download
Dell 3WY51 Firmware Upgrading Instruction Download Page 8

Upgrade Dell EMC Networking N1500 Series Switches  

 

 

 

Page 6

 

 

Programming controller register 

ddr_init2: MemC initialization complete 

Validate Shmoo parameters stored in flash ..... OK 

Press Ctrl-C to run Shmoo ..... skipped 

Restoring Shmoo parameters from flash ..... done 

Running simple memory test ..... OK 

DeepSleep wakeup: ddr init bypassed 3 

DDR Interface Ready 

CPLD: addr=0x21, rev=10 

Board: L2 48 Port Copper POE+ Switch, X01 

DRAM:  1 GiB 

NAND:   Micron MT29F1G08ABADA, 128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit 

NAND:   chipsize 128 MiB 

In:    serial 

Out:   serial 

Err:   serial 

arm_clk=1000MHz, axi_clk=400MHz, apb_clk=100MHz, arm_periph_clk=500MHz 

Unlocking L2 Cache ...Done 

l2cc_invalidate - Done, i = 981, invway = 0 

Net:   Registering eth 

Broadcom BCM IPROC Ethernet driver 0.1 

Using GMAC0 (0x18022000) 

et0: ethHw_chipAttach: Chip ID: 0xdb56; phyaddr: 0x1 

ethHw_miiphy_write (addr&f):phyaddr (addr&1f00):bank 

ethHw_miiphy_write phyaddr(0x1) bank(0x0) reg(0x0) data(0x2100) 

bcmiproc_eth-0 

========== relocate address: 0xdff7c000, offset 0xc1f7c000 ========== 

boot in 3 s 

Creating 1 MTD partitions on "nand0": 

0x000000200000-0x000007000000 : "mtd=4" 

UBI: attaching mtd1 to ubi0 

UBI: physical eraseblock size:   131072 bytes (128 KiB) 

UBI: logical eraseblock size:    126976 bytes 

UBI: smallest flash I/O unit:    2048 

UBI: VID header offset:          2048 (aligned 2048) 

UBI: data offset:                4096 

1 ecc_errors after reading 2320800:2320a00 

UBI: attached mtd1 to ubi0 

UBI: MTD device name:            "mtd=4" 

UBI: MTD device size:            110 MiB 

UBI: number of good PEBs:        880 

UBI: number of bad PEBs:         0 

UBI: max. allowed volumes:       128 

UBI: wear-leveling threshold:    4096 

UBI: number of internal volumes: 1 

UBI: number of user volumes:     1 

UBI: available PEBs:             8 

UBI: total number of reserved PEBs: 872 

UBI: number of PEBs reserved for bad PEB handling: 8 

UBI: max/mean erase counter: 37/16 

UBIFS: recovery needed 

UBIFS: recovery deferred 

UBIFS: mounted UBI device 0, volume 0, name "fs" 

UBIFS: mounted read-only 

UBIFS: file system size:   107802624 bytes (105276 KiB, 102 MiB, 849 LEBs) 

UBIFS: journal size:       5459968 bytes (5332 KiB, 5 MiB, 43 LEBs) 

Summary of Contents for 3WY51


















Reviews:

No comments

Brands by name

Popular brands

Load more brands