Firmware Upgrade Procedure Dell™ Networking N2100 Series Switches
Page 5
DRAM: 1008 MiB
WARNING: Caches not enabled
Bad bus: 2
NAND: (ONFI), MT29F32G08ABAAAWP , blocks per lun: 1000 lun count: 1
NAND: 1024 KiB blocks, 8 KiB pages, 16B OOB, 8-bit
NAND: chipsize 4096 MiB
EEPROM: TlvInfo v1 len=173
soc_pcie_hw_init : port->reg_base = 0x18012000 , its value = 0x1
PCIe port in RC mode
==>PCIE: LINKSTA reg 0xbe val 0x1001
**************
port 0 is not active!!
**************
In: serial
Out: serial
Err: serial
CLOCKS:ARM Core=1000Hz, AXI=500Hz, APB=125Hz, Peripheral=500Hz
USB0: Bringing USB2 host out of reset...
EEPROM: TlvInfo v1 len=173
EEPROM: TlvInfo v1 len=173
Net: eth-0
boot in 3 s
Creating 1 MTD partitions on "nand0":
0x000004e00000-0x000100000000 : "mtd=6"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 1048576 bytes (1024 KiB)
UBI: logical eraseblock size: 1032192 bytes
UBI: smallest flash I/O unit: 8192
UBI: VID header offset: 8192 (aligned 8192)
UBI: data offset: 16384
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=6"
UBI: MTD device size: 4018 MiB
UBI: number of good PEBs: 4014
UBI: number of bad PEBs: 4
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 44
UBI: total number of reserved PEBs: 3970
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 3/2
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 0, name "open"
UBIFS: mounted read-only
UBIFS: file system size: 4042063872 bytes (3947328 KiB, 3854 MiB, 3916 LEBs)
UBIFS: journal size: 33030144 bytes (32256 KiB, 31 MiB, 32 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 5182151 bytes (5060 KiB)
Loading file '/image2' to addr 0x70000000 with size 27624092 (0x01a5829c)...
Done
## Booting kernel from Legacy Image at 70000074 ...
Image Name: System for iproc_bri
Image Type: ARM Linux Multi-File Image (gzip compressed)
Data Size: 27623912 Bytes = 26.3 MiB
Load Address: 61008000
Entry Point: 61008000
Contents:
Image 0: 2636152 Bytes = 2.5 MiB
Image 1: 1794839 Bytes = 1.7 MiB
Image 2: 474 Bytes = 474 Bytes
Image 3: 23192424 Bytes = 22.1 MiB
Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 70000074 ...
