Dell 1537 - Studio Core 2 Duo T6400 2.0GHz 4GB 320GB Service Manual Download Page 1

Page: 1 / 41

Dell™ Studio 1535/1536 Service Manual

Before You Begin

Base Cover

Coin-Cell Battery

Memory

Hard Drive

Processor Thermal-Cooling Assembly

Processor Module

Center Control Cover

Keyboard

Wireless Mini-Card

Display

Camera

Palm Rest

Speaker Assembly

Optical Drive

USB/Audio Board

Microphone

System Board Assembly

Battery Latch Assembly

Flashing the BIOS

Notes, Notices, and Cautions

If you purchased a Dell™ n Series computer, any references in this document to Microsoft

Windows

operating systems are not applicable.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text:

Dell

and the

DELL

logo are trademarks of Dell Inc.;

Microsoft

Windows, and Windows Vista

are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries;

Bluetooth

is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under license.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.

Model: PP33L

May 2008 Rev. A00

NOTE:

A NOTE indicates important information that helps you make better use of your computer.

NOTICE:

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION:

A CAUTION indicates potential for property damage, personal injury, or death.

Summary of Contents for 1537 - Studio Core 2 Duo T6400 2.0GHz 4GB 320GB










































Search results

Summary of Contents for 1537 - Studio Core 2 Duo T6400 2.0GHz 4GB 320GB

Reviews:

Related manuals for 1537 - Studio Core 2 Duo T6400 2.0GHz 4GB 320GB

Brands by name

Popular brands

Dell 1537 - Studio Core 2 Duo T6400 2.0GHz 4GB 320GB, Service Manual

Search results

Summary of Contents for 1537 - Studio Core 2 Duo T6400 2.0GHz 4GB 320GB

Reviews:

Related manuals for 1537 - Studio Core 2 Duo T6400 2.0GHz 4GB 320GB

Brands by name

Popular brands