manualshive.com logo in svg

Dell EMC Unity All Flash, Field Upgrade Procedure

Share
Download
Dell EMC Unity All Flash Field Upgrade Procedure Download Page 11

equipment, the ordering process, and Links to training material. The Lift Tool Training
Video and Demo on Lift tool using the Voyager assembly (Voyager is the name given
to a Disk enclosure used in several products), are also linked on this page.

Note

If you are using a portable lift other than the Alum-A-Lift, adapt these instructions as
necessary while following all required safety requirements.

CAUTION

The portable lift commonly used by service personnel has two configurations -
one with the lower mast only and one with both the lower and upper masts. The
lower mast configuration is rated for 400 pounds and is for raising or lowering
objects 28U (49 inches) or less above the floor. The dual mast configuration is
rated well under 200 pounds and is for raising objects more than 28U (49 inches)
above the floor.

l

For installations at or below 49 inches, you must use the lower mast
configuration.

l

For installations above 49 inches, use the "Voyager" conversion kit, rated for
225 pounds, and a support table with the lower mast configuration.

Planning your lift

You can use the lift positioned along the side of the DAE or directly in the front of it.

If possible, position the lift adjacent to the LONG side of the enclosure. This reduces
the front clearance required to 50". Aligning the portable lift perpendicular to the
chassis also reduces the possibility of the chassis sliding off the lift and negates the
requirement to adjust the arm width to approximately 17".

Table 5 Planning your lift

Lift
position

Required front
clearance

Arm tray width

Notes

Side (long)

50"

Greater than 18"

Best practice, more stable

Front
(short)

60"

Between 16-17"

Requires arm adjustment, less stable
Refer to: 

Adjusting the arms for a frontal lift

 on page 13

Adding an optional 80-drive DAE

Working with the portable lift

     

11

Summary of Contents for Unity All Flash









































Reviews:

No comments

Brands by name

Popular brands

Load more brands