Display Cases 724, 7000, 9000 Series Service and Installation Manual
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
4
Display Cases 724, 7000, 9000 Series Service and Installation Manual
5
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
7000 Series
The optional wall mount kit is designed to securely hold a
7000 Series unit to a structurally sound wall. It meets the
requirements as established by Underwriter’s Laboratories
of withstanding a static load of four times the weight of the
cabinet alone.
The Delfield Company cannot assume
any responsibility for damage to a wall
or injury of any persons should the wall
fail as a result of the unit’s weight. Nor
will The Delfield Company assume any
responsibility for damage or injury as a
result of the wall mount fixture failing if it is
determined that the installation instructions
were not properly followed.
List of materials
2 — 2" x 2" x 3/16" (5.1 cm x 5.1 cm x 0.2 cm) angled
aluminum brackets, 48" (121.9 cm) long
12 — #10 x 7/8" type A hex head metal screws
6 — 1/4" x 2–1/2" lag bolts
2 — stainless steel trim pieces
1 Position the prepunched aluminum bracket
on the top of the unit, flush with the back
edge, and mark the location of the holes
on the unit. There should be one hole
approximately 5/8" (1.6 cm) from each end
of the cabinet, and a third hole 8.75" (22.2
cm) from the right end of the cabinet. Be
sure to use the prepunched holes; screws
in these locations tie into the internal
support structure of the unit.
2 Drill 9/64" (3.6 mm) holes at the locations
as marked. Attach the bracket to the unit
with three of the #10 sheet metal screws.
3 Mount the bottom bracket to the wall.
On a stud wall, the bottom bracket should be screwed into a
minimum of three studs with the provided 1/4" x 2–1/2" lag
bolts. On a masonry block wall, the bottom bracket should be
screwed into the wall at a minimum of three evenly spaced
locations with 1/4" diameter toggle bolts (not provided).
When positioning the bottom bracket, be sure to allow at
least 6" (15.2 cm) of clearance above and below the unit. Be
sure the bottom bracket is level before continuing.
4 Position the unit on the bottom bracket and
attach the top bracket to the wall using the
same method as in step 3.
5 Attach the bottom bracket to the unit using
the prepunched holes and three of the #10
sheet metal screws.
WALL MOUNT INSTALLATION
6 Attach the stainless steel trim strips to the
left and right sides of the cabinet using
three #10 metal screws on each side.
9000 Series
The Delfield Company cannot assume
any responsibility for damage to a wall
or injury of any persons should the wall
fail as a result of the unit’s weight. Nor
will The Delfield Company assume any
responsibility for damage or injury as a
result of the wall brackets failing if it is
determined that the installation instructions
were not properly followed.
When choosing a location to mount your 9000 Series display
case, keep in mind that the entire unit must be removed from
the wall in order to clean the condenser. This must be done
on a regular basis, in most cases not longer than every three
months. Install the equipment in a location that will allow
easy removal for cleaning.
1 Two wall brackets are supplied with 36" and 48"
long units; three brackets are supplied with 60"
and 72" long units. Lag bolts are not supplied
(see below for recommended sizes). Use all
brackets provided for a secure installation.
On a stud wall, the brackets should be screwed into two
studs with 1/4" lag bolts so that 2.50" (6.4 cm) of the lag
bolt engages the stud. On a masonry block wall, the brackets
should be screwed into the wall at two evenly spaced loca-
tions with 1/4" diameter toggle bolts.
When positioning the brackets, be sure to allow at least 6"
(15.2 cm) of clearance above and below the unit.
2 After the brackets are attached to the wall
with one bolt in each, check that they are
level. Finish mounting the brackets.
3 Once the brackets are secure, lift the unit
into place and engage the angle bracket on
the back of the unit into the wall brackets.
S
T P
E S
S
T P
E S
