OPERATION
• Press the push-button starter
1
(
Fig. A, B, G, H & J
) to open the valve.
• Automatic shut-off after ~30 seconds (+5/-10 according to the European standard EN 816).
INSTALLATION
• In order to capture all of the spray, install the shower tray 10cm from the wall: we recommend recessed
shower trays or sloping gutters. If a small, raised shower tray is installed, the shower nozzle
can be replaced with a grid (Ref. GR) to concentrate the jet.
SPORTING shower panel with top inlet (Fig. A & C)
• Position the panel so that the shower nozzle
5
is 2.10m from the floor.
• Using the tool
31
(supplied) or a pair of circlip pliers unscrew the ring
3
and remove the cover
7
.
• Unscrew the 2 screws
4
using a Phillips screwdriver and remove the end-cap
2
.
• Mark and drill the 4 holes
6
and
6’
.
• Fix the panel in place using the 4 screws supplied (use rawl plugs that are suitable for the wall material).
• Install the filter
8
(supplied) and connect to the mixed water supply (we recommend installing
a thermostatic mixing valve upstream).
• Using a 3mm Allen key (not supplied), check that the stopcock
32
is wide open (anti-clockwise).
• Supply with water and check for leaks.
• Replace the cover
7
and tighten up the ring
3
using the tool
31
or a pair of circlip pliers.
• Replace the end cap
2
and tighten the 2 screws
4
.
SPORTING shower panel with back inlet (Fig. B, C, D, E & F)
• Position the panel so that the shower nozzle
5
is 2.10m from the floor (or the water supply is 2.17m
above the ground) (
Fig. B
).
• Using the tool
31
(supplied) or a pair of circlip pliers, unscrew the ring
3
and remove the cover
7
(
Fig. B & C
).
• Remove the inlet assembly
33
by unscrewing nut
34
(
Fig. D
).
• Do not lose the washer
36
(
Fig. D
).
• Close the stopcock
32
(clockwise) using a 3mm Allen key (not supplied) (
Fig. E
).
• Fully unscrew nut
35
(
Fig. E
).
• Turn the threaded screw
37
and tighten nut
35
by hand (
Fig. E
).
• Connect the mixed water supply (we recommend installing a thermostatic mixing valve upstream)
by screwing the threaded screw
37
into the wall fitting, making sure that the threaded part
has a waterproof seal. Tighten so that the groove
38
is in line with the mounting surface
39
(
Fig. F
).
• Using a 3mm Allen key (not supplied), check that the stopcock
32
is closed (clockwise), open the water
supply and check for leaks.
• Use a Phillips screwdriver to unscrew the two screws
4
and the end cap
2
(
Fig. B
).
• Position the panel, insert washer
36
and tighten nut
34
by hand (
Fig. D
).
• Mark and drill the 4 holes
6
and
6’
(
Fig. B
).
• Fix the panel in place using the 4 screws supplied (use rawl plugs that are suitable for the wall material).
• Open the stopcock
32
(anti-clockwise) using a 3mm Allen key (not supplied) (
Fig. E
).
• Slide the cap
40
into the slot on the cover
7
(
Fig. B
).
• Replace the cover
7
and tighten the ring
3
using the tool
31
(
Fig. B & C
).
• Replace the end-cap
2
, tighten the 2 screws
4
(
Fig. B
).
EN
Exposed, wall-mounted SPORTING shower (Fig. G)
• Position the shower diffuser
5
2.10m from the floor. If necessary, insert the white plastic wedge
between the shower head and the wall to equalise the tile thickness.
• Assemble the shower column
10
with the push-button starter
1
and the collar
11
. Put the white
PVC tubes
12
into the column.
• Insert the column into the hole beneath the shower diffuser
16
. Mark, drill then fix the column using
the 2 chrome-plated screws provided (use rawl plugs that are suitable for the wall type).
• Position the collar
11
in the middle of the column to cover the joint. Mark, drill then fix the collar
11
and the push-button starter
1
using the 4 screws provided (use rawl plugs that are suitable for the type
of wall).
• Install the filter
8
supplied to protect the non-return valve
9
and connect to the mixed water supply
(recommended max. 41°C for the UK and Ireland). Ensure that all the connections are waterproof.
Recessed, wall-mounted SPORTING shower (Fig. H & I)
• Recess the connection pipe and connectors
13-14
in the wall so that the shower diffuser
5
is 2.10m
from the floor. Take care to maintain the recessing dimensions of the unions (0-9 mm from the exterior
wall surface) (
Fig. I
).
• Remove the 2 plastic protective caps
15
(
Fig. I
).
• Screw the shower head
16
on to the upper connection screw
17
which is situated inside the recessed
upper union
14
.
• Screw the push-button starter
1
on to the lower connection screw
18
which is situated inside
the recessed lower union
14
.
• Mark, drill then fix the shower head
16
and the push-button starter
1
using the screws provided
(use rawl plugs that are suitable for the wall type).
• Install the supplied filter
8
to protect the non-return valve
9
and connect to the mixed water supply
(recommended max. 41°C for the UK and Ireland). Ensure that the all connections are waterproof.
Ceiling-mounted SPORTING shower (Fig. J)
• Fix the shower head
16
to the water supply.
• Mark, drill then fix the push-button starter
1
1.10m from the floor shower using the screws provided
(use rawl plugs that are suitable for the type of wall)
• Connect the push-button starter
1
and the shower head
16
with a tube 6/8
19
(not supplied).
• To ensure it operates correctly, restrict the length of 6/8 connecting tube and the number of elbows
to a minimum (a maximum of 1 elbow).
• Install the supplied filter
8
to protect the non-return valve 9 and connect to the mixed water supply
(recommended max. 41°C for the UK and Ireland). Ensure that the all connections are waterproof.
THE INSTALLER MUST ENSURE:
• THE SEAL AROUND THE RECESSING HOUSING IS WATERPROOF TO PREVENT ANY INGRESS OF
WATER;
• ANY WATER ACCIDENTALLY ENTERING THE RECESSING HOUSING (E.G. CONDENSATION, RUN
OFF, LEAKS, ETC.) HAS A DRAINAGE POINT TO PREVENT ANY STAGNATION;
• THE INTEGRITY OF THE SEALS BETWEEN THE STAINLESS STEEL WALL PLATE AND THE WALL
OR THE WALL PLATE AND THE TAP AT LEAST ONCE A YEAR, AND MAKE GOOD IF NECESSARY.
If this advice is not followed, water may leak into the wall. DELABIE cannot be held
responsible for any ingress.
FOR FURTHER INFORMATION PLEASE CALL DELABIE TECHNICAL SUPPORT UK: 01491 821821.
ALL OTHER MARKETS: +33 (0)3 22 60 22 74.
