background image

36FB, 54FB 

TURF BEAST 

 

 

Rev: Mar2011 

 

 

T

URF BEAST  

Finish Mower 

Safety Information 

TURF BEAST lawn mowers are designed to give safe 
and dependable service if operated according to 
instructions. Read and understand this owner’s 
manual before operating your lawn mower.  

Emission Control System Information 

The U.S. and California Clean Air Acts 
EPA and California regulations require all 
manufacturers to furnish written instructions 
describing the operation and maintenance of 
emission control systems. The following instructions 
and procedures must be followed in order to keep 
the emissions from your engine within the emission 
standards. 

Safety Label Locations 

Safety labels are located on your mower to warn 
you of potential hazards. Read them carefully. If a 
label comes off or becomes hard to read, contact 
your GXi Parts and Service, LLC for a replacement. 

Operator Responsibility 

Be sure that anyone who operates the lawn mower 
receives proper instruction. Know how to stop the 
lawn mower quickly in case of emergency. 
Understand the use of all controls, output 
receptacles and connections. Children should not 
operate the lawn mower without parental 
supervision.  

Safety Information and Warnings 

Mower Inspection 

For your safety, inspect the lawn mower before each 
use. Before you begin your inspection, be sure the 
following conditions are met: the lawn mower should 
be on a flat and level surface, with the ignition switch 
off, the key removed, and the blades disengaged. Also, 
disconnect the spark plug wires from the spark plugs 
and ground them against the engine to prevent 
inadvertent starting. 

DANGER: GASOLINE IS HIGHLY FLAMMABLE AND 
EXPLOSIVE. Do not add fuel while the engine is 
running or is hot. Keep open flames, sparks, and heat 
away from the fuel and store fuel in containers 
specifically designed for that purpose. ADD FUEL 
OUTDOORS ONLY AND IF THE FUEL IS SPILLED, DO 
NOT START THE ENGINE. Manually push the mower 
away from the spill and wipe up immediately. 

WARNING 

WARNING! Do not use your BEAST lawn mower to 
carry passengers. Keep bystanders, helpers, pets and 
children at a safe distance from the machine while it is 
in operation since rotating blades can throw rocks and 
other items, causing serious injury. Check the area 
before you begin mowing for stones, sticks, wire, and 
other foreign objects. These objects may become 
projectiles when struck by the mower. 

WARNING! Wear protective clothing while mowing. 
Long pants and safety glasses help reduce the risk of 
injury from thrown objects. Adequate footwear, such as 
steel toe shoes with aggressive soles, is recommended 
to help protect your feet and maintain traction on slopes 
or uneven grounds. Always wear hearing protection. 

WARNING 

1.  Walk around the mower and look for any fluid 

spills or leaks on or underneath the mower. 
Remove any and all excessive debris, dirt, and 
fluids. 

2.  Look for signs of damage or excessive wear. 

Check the tightness of all nuts, bolts, pins, and 
screws. Tighten any that may be loose and 
replace any that are missing. 

3.  Be sure the safety interlock controls are 

operating properly so that the engine cannot be 
started unless the ground speed control lever is 
in neutral and the blades are disengaged. 

4.  Check the mower blades for any damage or 

abnormal wear. Replace in sets so that they are 
balanced. 

5.  Check the tire pressure on all four tires. Do not 

exceed the recommended maximum indicated 
on the tire. 

6.  Check the belts for proper wear and correct 

tension. See pages 16 and 17 for instructions. 

7.  Check engine oil and air filters as recommended 

in the engine manufacturer’s manual. 

DANGER 

Summary of Contents for TurfBeast 36FB



























Reviews: