background image

36FB, 54FB 

TURF BEAST 

 

 

Rev: Mar2011 

 

 

T

URF BEAST  

Finish Mower 

11 

Operating Instructions 

Return to Neutral 

If the mower creeps or will not stop as desired when 
the handles are in neutral position, adjustments are 
necessary. 
CAUTION: Be sure the engine is OFF before you 
open the hydro access panel. 
 
1.  Remove the bolts to 

access hydro panel. 
 
 
 
 

2.  Using an 8 mm wrench, 

reach through the bottom 
of the hydro panel to the 
return-to-neutral set pin 
bolts. Loosen bolts on the 
side that needs adjusting. 

3.  Be sure the brake is in the 

OFF position. In a safe operator position, start the 
engine. 

4.  With the engine running, slowly move the handle 

on the side needing adjustment until that side 
comes to a complete stop. If the mower creeps 
forward, pull handle in reverse, If the mower 
creeps backward, pull the handle forward. 

5.  When the mower stops moving completely the 

hydro is in the neutral position. 

6.  Turn off the engine. 
7.  Slowly tighten the bolts without moving the plate. 
8.  With the bolts tightened, move to a safe operator 

position and start the engine.  

9.  If the creep has returned, repeat the process. 

Multiple iterations may be required.  

 
 
 
 
 
 
DANGER! Make certain the engine comes to a 
complete stop before putting you hands in the 
access panel. 
 
10.  Reinstall hydro access panel. 

Disengaging Hydrostatic Drive Units  

Before physically moving the mower when the engine is 
NOT running, the hydrostatic drive units need to be 
disengaged into free-wheel mode.  

 
 
 
 

 
 
 

 

 
 

 

 
 
 

To disengage these hydro units: 

1.  Remove the hydro tool stored under the hydro unit. 

 

2.  Use the hook on the hydro tool to pull the hydro 

release pin back and out. 
Repeat on the other side. It 
may be necessary to bump 
the hydro carrier forward 
for easier free-wheeling. 
 

CAUTION! Never bump, hit or 
push the actual hydros. 
 
To return to operation mode: 

1.  Slide the hydro tool 

through the hydro 
tensioner. Pull until the pin 
sets. Repeat on the other 
side. If the pin partially 
sets, tap the pin. 

2.  Replace the hydro tool to 

storage under the hydro unit. 

DANGER 

Hydro tool 

Hydro 

tensioner 

Hydro 

release 

pin 

Summary of Contents for TurfBeast 36FB



























Reviews: