background image

Page 

15

 of 

20

 

For more information:

  970.493.1901 or 

[email protected]

 

Document #7650-0038 Rev A1. © Copyright 2019 Directed Energy, Inc. All rights reserved.

 

7.0 TROUBLESHOOTING  

7.1 Troubleshooting Procedures  

Before attempting to service or troubleshoot the PVX-4140 B, review the safety 

summary above.  

The below information  summarizes potential problems and their solutions. If these 

recommendations do not resolve the problem, DEI customer service can be contacted 

for further assistance.  

  Power LED does not illuminate 

o

  AC power not plugged in 

o

  Fuse(s) are blown 

  Cannot enable output 

o

  External remote interlock circuit is not satisfied 

  No Output Pulse 

o

  Output is not enabled 

o

  External remote interlock circuit is not satisfied 

o

  No gate input 

o

  Gate input pulse voltage too low: Increase voltage 

o

  Gate input pulse width too narrow: Increase width 

o

  Gate input pulse frequency too high: Reduce frequency 

o

  No high voltage: Check HV supplies for correct operation 

o

  Output not connected correctly: Check all cables and connections 

o

  Instrument is damaged: Contact DEI customer service 

7.1.1 Fuses  

To avoid fire hazard or damage to the instrument, use only the fuse types listed on the 

rear panel. Fuse replacement should be performed by qualified personnel only. 

8.0 SYSTEM FAILURE MODES  

The PVX-4140 B is capable of generating large amplitude current pulses with very fast 

rise and fall times. There is limited over-current or over-voltage protection circuitry, and 

it is the user's responsibility to assure that the interconnect cables and load do not 

create transients, over-current or over-voltage conditions that could damage the PVX-

4140 B. FAILURE TO DO SO VOIDS THE WARRANTY.  

8.1 Over-Current Failure  

Depending on the value of load  voltage, the overcurrent limit may or may not be 

exceeded even when connected to a shorted load. Typically, the output voltage must 

be greater than 733 V. If the output voltage is in excess of 733 V and the load is 

shorted, then the Over Current LED should illuminate. Internally, this indicates that the 

Summary of Contents for PVX-4140 B





















Reviews: