background image

Page 

14

 of 

20

 

For more information:

  970.493.1901 or 

[email protected]

 

Document #7650-0038 Rev A1. © Copyright 2019 Directed Energy, Inc. All rights reserved.

 

6.0 OPERATING INSTRUCTIONS  

This section provides basic operating instructions for the PVX-4140 B.  Additional 

application information may be found in Section 7.0.  

WARNING 

 

1.  There are NO user serviceable items inside this instrument. The  cover  should 

NEVER be removed.  

2.  Do not remove the input or output cables while the instrument is in operation. Never 

short-circuit the output of the instrument. Failure to observe these precautions can 

result in potential electric shock to personnel, arcing, and damage to the connectors 

and system.  

3.  Pulsed power systems are capable of random triggering via transients. When the 

PVX-4140 B is turned on, or voltage is present in the chassis, assume it is possible 

to get a pulse on the output connector.  

6.1 Power-Up Procedures  

The instrument should be powered up using the procedures detailed in the Section 

above. When this is accomplished, it can be adjusted for the particular application 

through the following procedure:  

1.  Monitor the output of the PVX-4140 B on an oscilloscope utilizing a high voltage 

probe connected to the load, or with a coax attached to the Voltage Monitor output 

on the front panel.  Set the output amplitude of the PVX-4140 B to the desired level 

by adjusting the output voltage of the high voltage power supplies.  

2.  Set the output pulse width and pulse repetition frequency by varying the controls 

of the Gate  input pulse generator. The output pulse width should be set by 

monitoring the output of the PVX-4140 B. The output pulse voltage will follow the 

gate input, but will not replicate in time the exact duration of the Gate input due to 

the system propagation delay.  

6.2 Power-Down Procedures  

1.  Set the high voltage power supplies to zero.  

2.  Turn the high voltage power supplies OFF.  

3.  Turn the PVX-4140 B power switch OFF.  

4.  Allow the instrument to bleed off the stored energy (approximately five minutes). 

5.  Disconnect the AC power to the instrument.  

Summary of Contents for PVX-4140 B





















Reviews: