background image

 

15 

General warranty terms and conditions 

When following the instructions for installation, operation and maintenance, the manufacturer guarantee 24 months from 
the date of receipt for the product

. Should the product purchased be put into operation by an entity other than the seller, the 

warranty  period  commences  from  the  date  that  the  product  is  put  into  operation,  provided  that  the  buyer  ordered  its 
commissioning within three weeks of its receipt. The customer expressly acknowledges that during the warranty period that 
extends beyond the length of the warranty period that is specified in the Commercial Code (the statutory warranty) s/he can 
neither require replacement of the product nor may s/he withdraw from the contract. 

1.

 

When  claiming  a  product  defect  it  is  necessary  to  submit  a  proof  of  purchase  that  contains  the  following  information: 
name and surname, name and business name, address and the warranty card, if the buyer received one from the seller. 
The validity of the warranty shall not be affected  by non-compliance with the obligations related to the issuance of the 
warranty card. 

2.

 

Claims  concerning  the  product  (for  a  warranty  repair  only  complete  devices  are  accepted)  may  be  filed  during  the 
warranty  period  only  with  the  seller  from  which  it  was  purchased;  subsequently  the  seller  is  required  to  forward  the 
product to an authorised service centre or to the manufacturer.  

3.

 

A condition for the recognition of the rights under the warranty is the installation of the product having been undertaken 
by an authorised person in possession of a valid certificate from the manufacturer. 

5.

 

Claims regarding a product defect that can be dealt with reasonably quickly and without additional consequences will be 
resolved  by  remedying  the  defect  (repair)  or  by  replacement  of  the  product  part  ,  because  in  such  a  case  it  is  a 
contradiction  of  the  standard  norms  that  the  entire  product  shall  be  replaced  (§  616,  paragraph  4  of  the  Commercial 
Code). 

6.

 

The buyer who exercises the right of warranty repair is not entitled to the return of the parts that have been replaced.  

7.

 

The warranty period can be extended for up to 48 months and its validity can be extended beyond the standard length on 
the  basis  of  the  conclusion  of  an  individual  warranty  contract.  Further  information  may  be  obtained  through  a  specific 
business meeting. 
 

This warranty is not applicable to: 

 

a product that has not 

been put into operation by the manufacturer or by a certified employee

 in possession of a valid 

certificate issued by the manufacturer 

 

A product that did not have regulary performed calibrations and functional checks by the manufacturer or by a certified 
employee is possession of a valid certificate issued by the manufacturer. 

 

damage  caused  by  fire,  water,  static  electricity,  power  surges  in  the  electric  supply  or  in  the  public  network,  accident, 
improper use of the product, wear and tear 

 

contamination of the product and its subsequent cleaning 

 

damage caused by 

improper installation, any adjustment, modification

 or improper manner of use inconsistent with the 

instruction manual, the technical standards or the applicable safety regulations in the Czech Republic 

 

damage  to  the  product  during  transportation  caused  by  improper  handling  or  handling  of  the  product  in  a  manner 
contrary to the advice provided in the instruction manual 

 

DEGA products that have 

been used in association with other than original DEGA products

, including consumables and 

accessories

 

 

bearing additional parts or consumables (e.g. a foil label, seal, etc.), that are detrimental to normal wear and tear during 
operation, together with wear and tear of the product and its parts caused by their normal use

 

 
For the complete version of the general business conditions and of the claims procedure go to 

www.dega.cz

 

  
 
 
Manufacturer: DEGA CZ s.r.o., Malešická 2850/22c, 130 00 Praha 3, Czech republic 
VAT: CZ 279 029 43, Telephone: +420 774 447 660, E-mail: [email protected], Web: www.dega.cz 

 

 

© 2021 DEGA CZ s.r.o. 

 

 

User Manual ver.: 8/27/2021 2:19:00 PM 

 
 

Summary of Contents for 40100002
















Reviews: