11
Picture 7. Example of connection of DEFRO HOME AIRPELL stove to
flue with condensate discharge.
5.6.
CONNECTION TO ELECTRIC SYSTEM
Electrical installation of the DEFRO HOME AIRPELL dry stove is in-
tended for supply from mains with 230 V/50 Hz. Room, where the stove
is installed, should be equipped with electrical system 230V/50Hz exe-
cuted as TN-C or TN-S systems (with the protective conductor or pro-
tective-neutral conductor) according to the regulations in force. Electric
system (without regard for the type of installation made) should be
ended with plug-in socket equipped with protective conductor contact.
Plug-in socket should be located in the safe distance from the heat
emission source.
Using a socket without connected protective terminal
causes an electric shock hazard!
All connections to the electric system can be executed
only by the electrician having suitable certifications /of
the Polish Electricians Association 1kV/.
User is forbidden to take off covers of the electronic
controller or fan and to make any interventions or mod-
ification in electrical connections.
6.
USAGE AND OPERATION
Combustion chamber should be closed during operation of the stove.
So, it is forbidden to open the doors when the flame is burning in the
burner.
6.1.
INTRODUCTORY REMARKS
Do not touch stove during first firing-up, because the
paint is hardening during this stage.
Touching the paint could result in uncovering of the
steel surface.
It is possible to refresh it using spray paint of the same colour if neces-
sary.
It is good practice to ensure efficient ventilation during
first firing-up because small amounts of smoke and
paint odour will be emitted from the stove.
Do not stay near the stove. It is required to vent the room. Smoke and
paint odour will disappear after approx. one hour of operation. How-
ever, we remind that they are not harmful to health.
The stove is subject to expansion and shrinkage during warming and
cooling down stage what may cause slight squeaks. This is an abso-
lutely normal phenomenon because a structure of the equipment is
made rolled steel and this phenomenon shall not be considered as a
defect.
It is very important to avoid excessive overheating of the stove at the
beginning but to reach the required temperature gradually. Use low
heating powers. During the next firing-up of the stove, it will be possible
to use the whole available thermal power. This will avoid damage of
ceramic tiles, welds and steel structure.
Do not expect immediate effects of heating!
6.2.
FIRST START-UP AND OPERATION
6.2.1.
STOVE START-UP
Absolutely, before each starting of ignition function in
the controller the burner should be empty (no pellet
may be located inside).
Turn on the power supply.
1.
For a start-up with an empty feeder (first start-up or start-up when
whole fuel from the container has been used up) you should start-
up pellet feeder (endless screw):
a.
press button
,
b.
using buttons select
Menu Customization
Manual load,
c.
press again
,
a
d.
using
buttons select
ON
option and confirm
pressing .
e.
Shutdown the endless screw using
OFF
option when
you head pellet falling into the burner.
2.
Return to the main menu with a button
.
3.
Switch on
Ignition
with
button. Successive stages of the
combustion cycle will be carried out automatically.
4.
Please inspect the size and brightness of the flame for 15-20
minutes during the combustion process, when the stove is in “
op-
eration
” mode. It should have a length of approx. 20-40cm during
operation with 100% rated power - depending on the size of the
stove (burner).
More information concerning servicing the controller is included in the
NG01 HYDRO controller’s operating manual.
Housing components will be very hot during operation.
You must exercise caution.
6.2.2.
REFUELLING
Fuel should be refilled on a regular basis to ensure that is level does
not fall below 10-25% of maximum loading. Use caution during refuel-
ling, in particular when the stove is hot. After opening cover of the con-
tainer the pellet should be added vigorously, with short breaks allowing
proper setting of the fuel. Close the cover tightly as soon as the refuel-
ling is completed, in particular when the stove is in operation.
Avoid contact of pellet packaging (e.g. bags) with hot components of
the stove. Take care to avoid getting other materials than pellet into the
container. Pieces of fuel larger than the allowable size of the pellet may
result in jamming or damage of mechanism of the feeder.
It is forbidden to use another type of fuel than the pellet. Fuel should
be stored in a safe distance from the stove (minimum 2 m from the
stove).
6.2.3.
DAMPING
Routine damping of the stove is based on the selection of the
Damping
function from the controller menu. The controller will lock fuel feeding
and the stove will be damped after combustion of the current dose of
flue with
condensate discharge
rosette
mortar
non-flammable
material
cleaning opening
SET
SET
SET
ESC
