background image

The C/L/R 2500 is supplied with brass inserts designed to go into the bottom

of the speaker to hold adjustable feet which hold the speaker above the surface
it is placed on as well as give you the option of angling the speaker up or down
to point directly at the listeners. Install three of these inserts in the bottom of the
speakers. There are predrilled holes on the bottom of the speaker under the grill
cloth (when the speaker is positioned horizontally). Simply locate the holes.
Two holes are 2'' back from the front and 15 

1

/

16

'' apart. You also have a choice

for the rear hole depending on the depth of the surface you will place the speak-
er on. They are located along the center line going from the front and the back
of the speaker on the bottom. Then feel for them and select one of these holes.
Gently tap the inserts in through the grill cloth and screw the feet in.

Service and warranty work on your Definitive loudspeakers will normally be

performed by your local Definitive Technology dealer. If, however, you wish to
return the speaker to us, please contact us first, describing the problem and
requesting authorization as well as the locations of the nearest factory service
center. 

Please note that the address given in this booklet is the address of

our offices only. Under no circumstances should loudspeakers be shipped

to our offices or returned without contacting us first and obtaining return

authorization.

Definitive Technology Offices
11433 Cronridge Drive
Owings Mills, Maryland 21117
Phone: 410-363-7148

Service

Because the C/L/R 2500 can be used either vertically or horizontally, the

logo is supplied separately. Holes are provided for installation when the speak-
er is used horizontally. These are located under the grill cloth at the center of
the lower edge at the front of the speaker approximately 

11

/

16

'' up from the edge

and 1 

1

/

2

'' apart. Locate the logo over these two holes and gently tap it in

through the grill cloth.

Installing the Logo

Installing the Feet/Angling Device

Technical Assistance

It is our pleasure to offer assistance if you have any questions regarding

your C/L/R 2500s or their set-up. Please contact your nearest Definitive
Technology dealer or contact us directly at 

410-363-7148 or www.defini-

tivetech.com.

Visit us at www.definitivetech.com

13

Summary of Contents for C/L/R 2500















Reviews: