manualshive.com logo in svg

Dedoes MPU02, Manual, Page: 1 / 10

Share
Download
Dedoes MPU02 Manual Download Page 1

Call or Visit @ 248-624-7710 / www.dedoes.com

Manual Propor�oning Unit 

PART # P2764 KD RV.0 - 2022-05-12

Dedoes P# MPU02

How to perform a pressure test on a MPU02

• Perform a pressure test after each repair or replacement of parts within the MPU02 before use to ensure there are no leaks.

• Turn both of the front pump valves to the "ON" position.

• Unscrew the wetting cup and set it aside.

• Visually check that both pump pistons go completely down within each pump and are adjusted correctly.

• Pour one quart of reducer in a container and place under front pump.

• Place both of the front pump suction hoses into the front container with the reducer.

• Pour one quart of reducer into a container and place under the rear pump.

• Place the rear pump suction hose into the rear container with the reducer.

• Pump the lever in quick short strokes making sure the lever is going completely down until both pumps are primed. 

• Once the air is pumped out of the pumps, pump the lever one full stroke and verify that the pumps are working correctly. 

• With the lever at the half stroke and reducer filling the pumps, block the end of one of the discharge tubes with your finger. 

• Pull the lever down firmly and hold it down. 

• Visually inspect the seals in each pump to be sure that fluid does not by-pass the seals. 

• Visually check all connections of the pump for any leakage. If none, lift lever slightly to release your finger. 

• Verify that both pump assemblies and hose assemblies do not leak under pressure using the steps above.

• Pull the lever down completely.  

• Remove the full container and replace it with an empty container. 

• Pump the unit until both pumps are empty. 

• Shake suction the hoses to drain as much fluid as possible. 

• Leave the hoses hanging to air dry.

• Wipe the unit off using paper towels.

• Screw the wetting cup in place.

• Place new product on the MPU02 and prime the pumps. (Refer to the user manual for priming instructions) 

• Dispense enough fluid to ensure the reducer has been flushed from MPU02 unit entirely. 

• Dedoes suggests a spray panel test to verify clear coat finish quality.

MPU Maintenance and Repair Guide

Summary of Contents for MPU02











Reviews:

No comments