manualshive.com logo in svg

Decware TORIIMONO, Owner'S Manual

Share
Download
Decware TORIIMONO Owner'S Manual Download Page 6

              O W N E R S   M A N U A L                

               

Decware High Fidelity Engineering Co.,  East Peoria IL, USA   www.decware.com    

                                           

STARTING YOUR AMPLIFIER FOR THE 

FIRST TIME

Once you have the tubes installed and the power cord plugged in, the volume control 
all the way down (counter-clockwise) you are almost ready to turn it on.  BEFORE YOU 
DO, we need to familiarize you with the BIAS controls.  There are only two and they 
are extremely easy to operate. (

after the amplifier is turned on and properly 

biased, we will connect your source component.

)

We’ll start with the most important of the two controls, the one in the front of amplifier 
located between the two meters.  It is a small 1/4 inch shaft with no knob on it.  The 
knob is not used because this control is seldom adjusted, and a knob makes it easier 
to accidentally bump it out of adjustment.  

This control

 is called the 

BIAS BALANCE 

KNOB

 and it is simply used to make the two meters read the same value.

In the picture above you can see the meter on the left is for the KT88 output tube 
directly behind it.  Same for the meter on the right.  These meters show how many 
milliamps of current are going through each output tube.  Since this is a push pull 
amplifier, the objective is to get both tubes to draw the same amount of current so that 
they match.  This gives the best performance and the most power.

Summary of Contents for TORIIMONO



















Reviews:

No comments

Brands by name

Popular brands

Load more brands