manualshive.com logo in svg

Decware TORIIMONO, Owner'S Manual

Share
Download
Decware TORIIMONO Owner'S Manual Download Page 12

OPERATION

If you’ve been going through this manual (highly highly recommended) and reached 
this point, we know you’re already listening to music and we’ll probably never see you 
again... but a few additional notes...

TYPE OF AMP

Your Class A amplifiers are a push-pull design with an adjustable fixed bias using ultra-
linear output transformers with multiple taps for different loudspeakers.  It is a design 
with the fewest internal parts of any push pull amplifier featuring direct coupled stages 
for maximum transparency and minimal phase angle.

SAFTEY

Your amplifiers are fused, however with all devices that generate heat it is not 
recommended to leave the amplifier on when you are not at home, or during the night 
when you are sleeping.   There are no internal user serviceable parts inside this 
amplifier.

OPTIONS

Your amplifier comes with a pair of Jensen JT11P1 balancing transformers to cover 
most applications, however, any of the balancing transformers Jensen makes can be 
requested for custom applications in recording studio environments.

              O W N E R S   M A N U A L                

               

Decware High Fidelity Engineering Co.,  East Peoria IL, USA   www.decware.com    

                                           

Summary of Contents for TORIIMONO



















Reviews:

No comments

Brands by name

Popular brands

Load more brands