2
1.0 APPLICATION
1.1 PURPOSE:
The Sa
fl
ok
™
Pole Anchor System is is a Vertical Lifeline System for use as part of a Personal Fall Arrest
System (PFAS) when climbing and working on wooden utility poles (power poles, telephone poles, etc.).
1.2 STANDARDS:
Refer to local, state, and federal (OSHA) requirements governing occupational safety for
additional information regarding Personal Fall Arrest Systems. Refer to the following national standards on fall
protection:
ANSI Z359-0
De
fi
nitions and Nomenclature User for Fall Protection and Fall Arrest
ANSI Z359-1
Safety Requirements for Personal Fall Arrest Systems, Subsystems, and Components
ANSI Z359-2
Minimum Requirements for a Comprehensive Managed Fall Protection Program
CSA
Z259.2.1
Fall Arrestors, Vertical Lifelines, and Rails
1.3 TRAINING:
This equipment is intended to be used by persons trained in its correct application and use. It is the
responsibility of the user to assure they are familiar with these instructions and are trained in the correct care and use
of this equipment. Users must also be aware of the operating characteristics, application limits, and the consequences of
improper use.
2.0 SYSTEM LIMITATIONS & REQUIREMENTS
Consider the following limitations/requirements prior to installing or using this equipment:
2.1 CAPACITY:
This equipment is designed for use by a one climber at a time. Combined weight of the climber
(person, clothing, tools, etc.) should not exceed 310 lbs (141 kg).
2.2 ANCHORAGE:
In accordance with ANSI Z359.1, anchorages selected for Fall Arrest Systems must have a
strength capable of sustaining static loads applied in the directions permitted by the system of at least:
Non-Certifi ed Anchorages:
5,000 lbs (22.2 kN)
Certifi ed Anchorages:
2 times the Maximum Arresting Force
2.3 FALL ARREST FORCES:
The Personal Fall Arrest System must limit fall arrest forces to 1,800 lbs (8 kN) and
deceleration distance must not exceed 42 inches (107 cm).
2.4 FREE
FALL:
Per ANSI Z359.1, Personal Fall Arrest subsystems used with the Pole Anchor System must limit free
fall to 6 feet (1.8 m). To avoid increased fall distance, do not work above the anchorage level.
2.5 FALL
CLEARANCE:
Ensure that adequate clearance exists in the fall path to prevent striking an object during
a fall. The clearance required is dependent on the type of connecting subsystem (rope grab, lanyard), the
anchorage location, and the elongation characteristics of the lifeline. Table 1 approximates elongation for varied
lengths of dry Lifeline. Wet Lifelines generally elongate further than dry Lifelines.
Table 1 - Lifeline Elongation
Lifeline Length
10 ft
(3.0 m)
20 ft
(6.1 m)
30 ft
(9.1 m)
40 ft
(12.2 m)
50 ft
(15.2 m)
60 ft
(18.3 m)
70 ft
(21.3 m)
80 ft
(24.4 m)
Elongation:
0.4 ft
(11.1 cm)
0.7 ft
(22.6 cm)
1.1 ft
(33.7 cm)
1.5 ft
(45.2 cm)
1.9 ft
(56.3 cm)
2.2 ft
(67.5 cm)
2.6 ft
(78.7 cm)
3.0 ft
(90.1 cm)
2.6 ENVIRONMENTAL
HAZARDS:
Use of this equipment in areas where environmental hazards exist may require
additional precautions to reduce the possibility of injury to the user or damage to the equipment. Hazards may
include, but are not limited to: high heat, caustic chemicals, corrosive environments, high voltage power lines,
explosive or toxic gases, moving machinery, or sharp edges.
2.7 BODY
SUPPORT:
A Full Body Harness must be used with the Sa
fl
ok Pole Anchor System. The harness
connection point must be above the user’s center of gravity. A body belt is not authorized for use with the
Pole Anchor System. If a fall occurs when using a body belt it may cause unintentional release and possible
suffocation because of improper body support. Substitutions of equipment or system components must not be
made without the written consent of Capital Safety.
2.8 COMPATIBILITY OF COMPONENTS:
Unless otherwise noted, DBI-SALA equipment is designed for use with
DBI-SALA approved components and subsystems only. Substitutions or replacements made with non approved
components or subsystems may jeopardize compatibility of equipment and may affect safety and reliability of the
complete system.
