7
E
n
g
lis
h
E
n
g
lis
h
8
COMMANDS AND FUNCTIONS
1)
“VOLUME” CONTROL
The knob regulates the diffuser's volume.
This control does not affect the output “LINK” levels.
2)
“LIMITER” INDICATOR LIGHT
The “LIMITER” indicator light comes on red during start (for a few seconds) and
when the internal audio limiter engages. This avoids the amplifier's distortion and
protects the loudspeakers against overloads.
3)
“POWER” INDICATOR LIGHT
The “POWER” indicator light comes on green to indicate that the amplifier is
switched on and it is working properly.
5)
“BALANCED INPUTS LINK” CONNECTORS
These balanced inputs can be used to connect audio sources at line level (0dB)
(eg. preamplifier, mixer, recorder, CD player, musical instrument, ...).
The balanced connector is connected in parallel and can be used to send the audio
signal to other amplified speakers, recorders or supplementary amplifiers.
6)
POWER SWITCH “POWER”
This switch can be used to switch the diffuser on and off.
7)
POWER CABLE SOCKET “MAINS”
Used for connecting the power cable supplied.
8)
FUSE CARRIER “FUSE”
Mains fuse housing.
9)
VOLTAGE CHANGE “VOLTAGE SELECTOR”
For changing the power voltage of the speaker (240V/120V).
This switch is preset and protected by the manufacturer.
AMPLIFIER PANEL (PIC.1)
4)
EQUALIZATION CONTROL
This control permits the equalization of the speaker.
The "FLAT" central position permits a linear sound reproduction of the speaker. By
turning the control towards “VOICE”, the response curve of the speaker highlights
the mid frequencies while if the control is turned towards ”MUSIC”, the low and high
frequencies are highlighted.
This control does not affect the level of the output signal (link).
ROTATING HORN
Speakers are always supplied by the manufacturer with the horn driver positioned
horizontal at 90°
.
If you wish to change the coverage angle (PIC. 2):
-
undo the fixing screws of the grille
-
remove the front protective grille by slightly pressing on one side and taking the
grille off the special slots
-
undo the eight fixing screws of the horn
-
rotate the horn in the desired position (the horn should never be removed from the
loudspeaker)
-
tighten the fixing screws of the horn
-
put the grille back in the special side slots and tighten the screws of the grille.
TECHNICAL DATA AND DIMENSIONS
TECHNICAL DATA
M10-2 PLUS
M12-4 PLUS
System
ACTIVE / BI-AMPS
ACTIVE / BI-AMPS
Type of amplifier
HIGH - class AB
HIGH - class AB
LOW - class H
LOWI - class H
RMS Power
150W LF + 50W HF
250W LF+50W HF
Musical power
300W LF + 100W HF
500W LF+100W HF
Frequency response (-3dB)
70 - 19.000 Hz
68 - 19.000 Hz
Crossover
Ft 2000 Hz
Ft 2000 Hz
DR 12 dB/oct
CD 12 dB/oct
W 12dB/oct
W 12dB/oct
Sound pressure (SPL)
120 dB max
126 dB max
Components
1 x woofer 10"
1 x woofer 12”
voice coil 2”
voice coil 2”
1 x driver 1"
1 x compress. Driver 1,4”
voice coil 1” exit
voice coil 1” exit
Dispersion
90°x70° (rotary)
90°x70° (rotary)
Input sensitivity
0dB
0dB
Impedance input balace
30K
W
30K
W
Alimentation
see label on the box
Dimensions (LxHxP)
380x286x493 mm
400x387x525 mm
Weight
13,7 Kg
18,4 Kg
Flying support
---
10MA x 3 points
Stan standard stirrup
---
D36mm
LOUDSPEAKER INSTALLATION
WARNING
Make sure that the loudspeaker in securely installed in a stable position to avoid any
injuries or damages to persons or property.
For safety reasons do not place one loudspeaker on top of another without proper
fastening systems. Before hanging the loudspeaker check all the components for
damages, deformations, missing or damaged parts that may compromise safety during
installation.
If you use the loudspeakers outdoors avoid places that are exposed to bad weather.
The loudspeaker has the following mounting options:
-
floor (monitor) (FIG.3)
-
standmount - only for M12-4 PLUS (FIG.4)
-
suspended with support rails or brackets supplied by the manufacturer - only for
M12-4 PLUS (FIG.5)
