Daytona ANIMA 190FSM Owner'S Manual Download Page 18

Page: 18 / 21

PRE-OPERATION INSPECTION AND MAINTENANCE

ENGINE OIL TEMPERATURE CONTROL

WARNING

Engine oil temperature is to be strictly controlled at 90 degrees Celsius (194 degrees

Fahrenheit) or lower.

Serious damage will occur in the engine if engine oil temperature exceeds 90 degrees

Celsius or 194 degrees Fahrenheit.

It is solely customer’s responsibility to control the engine oil temperature.

Any failures caused by overheating are NOT considered as the defects of Products.

It is highly recommended to use HIGH-EFFICIENT OIL COOLER and OIL TEMPERATURE

GAUGE to protect the engine.

The above OIL COOLER is just a recommendation.

Engine oil temperature can be heated up over

90 degrees Celsius or 194 degrees

Fahrenheit, even if the above recommended OIL COOLER is used.

Again, customer needs to control the oil temperature very carefully.

Summary of Contents for ANIMA 190FSM






















Search results

Summary of Contents for ANIMA 190FSM

Reviews:

Related manuals for ANIMA 190FSM

Brands by name

Popular brands

Daytona ANIMA 190FSM, Owner'S Manual

Search results

Summary of Contents for ANIMA 190FSM

Reviews:

Related manuals for ANIMA 190FSM

Brands by name

Popular brands